Update Makefile

diff --git a/keyboards/jd40/Makefile b/keyboards/jd40/Makefile
index 242748111c010b1b30202f5ebd911415ece7810d..57b2ef62e5f3a43b7338f789a5d4800c577b763d 100644 (file)
--- a/keyboards/jd40/Makefile
+++ b/keyboards/jd40/Makefile
@@ -1,74 +1,3 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes                # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes         # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes         # Audio control and System control(+450)
-# CONSOLE_ENABLE ?= yes                # Console for debug(+400)
-# COMMAND_ENABLE ?= yes                # Commands for debug and configuration
-KEYBOARD_LOCK_ENABLE ?= yes    # Allow locking of keyboard via magic key
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE ?= yes      # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes                     # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-# BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
-# MIDI_ENABLE ?= YES                   # MIDI controls
-# UNICODE_ENABLE ?= YES                # Unicode
-# BLUETOOTH_ENABLE ?= yes      # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE ?= yes          # Enable RGB Underglow
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
        include ../../Makefile
 endif
-