+++ /dev/null
-#include "deltasplit75.h"
\ No newline at end of file
+++ /dev/null
-#ifndef deltasplit75_H
-#define deltasplit75_H
-
-#ifdef SUBPROJECT_v2
- #include "v2.h"
-#endif
-#ifdef SUBPROJECT_ProtoSplit
- #include "ProtoSplit.h"
-#endif
-
-#include "quantum.h"
-
-#endif
\ No newline at end of file
+++ /dev/null
-SUBPROJECT_DEFAULT = v2
-
-ifndef MAKEFILE_INCLUDED
- include ../../Makefile
-endif
+++ /dev/null
-ifndef MAKEFILE_INCLUDED
- include ../../Makefile
-endif
\ No newline at end of file
+++ /dev/null
-#include "DeltaSplit75.h"
-
-#ifdef AUDIO_ENABLE
- float tone_startup[][2] = SONG(STARTUP_SOUND);
- float tone_goodbye[][2] = SONG(GOODBYE_SOUND);
-#endif
-
-void matrix_init_kb(void) {
-
- #ifdef AUDIO_ENABLE
- _delay_ms(20); // gets rid of tick
- PLAY_NOTE_ARRAY(tone_startup, false, 0);
- #endif
-
- // // green led on
- // DDRD |= (1<<5);
- // PORTD &= ~(1<<5);
-
- // // orange led on
- // DDRB |= (1<<0);
- // PORTB &= ~(1<<0);
-
- matrix_init_user();
-};
-
-void shutdown_user(void) {
- #ifdef AUDIO_ENABLE
- PLAY_NOTE_ARRAY(tone_goodbye, false, 0);
- _delay_ms(150);
- stop_all_notes();
- #endif
-}
+++ /dev/null
-#ifndef ProtoSplit_H
-#define ProtoSplit_H
-
-#include "../DeltaSplit75.h"
-
-//void promicro_bootloader_jmp(bool program);
-#include "quantum.h"
-
-//void promicro_bootloader_jmp(bool program);
-//matrix is defined in a weird way here; the layout on both sides are asymmetrical, but the "matrix" is symmetrical but with empty gaps
-//the last column is defined as a separate row because the firmware currently doesnt support more than 8 columns (this layout has 9 columns per side) K45 and K110 are the Bs on both sides
-#define KEYMAP( \
- K00, K01, K02, K03, K04, K05, K06, K70, K71, K72, K73, K74, K75, K76, K77, K132, \
- K10, K11, K12, K13, K14, K15, K16, K80, K81, K82, K83, K84, K85, K86, K87, K133, \
- K20, K21, K22, K23, K24, K25, K90, K91, K92, K93, K94, K95, K96, K97, K134, \
- K30, K31, K32, K33, K34, K35, K100, K101, K102, K103, K104, K105, K107, K135, \
- K40, K41, K42, K43, K44, K45, K110, K111, K112, K113, K114, K115, K116, K117, K136, \
- K50, K51, K52, K54, K55, K120, K121, K122, K123, K126, K127, K137 \
- ) \
- { \
- { K00, K01, K02, K03, K04, K05, K06, KC_NO}, \
- { K10, K11, K12, K13, K14, K15, K16, KC_NO}, \
- { K20, K21, K22, K23, K24, K25, KC_NO, KC_NO}, \
- { K30, K31, K32, K33, K34, K35, KC_NO, KC_NO}, \
- { K40, K41, K42, K43, K44, K45, KC_NO, KC_NO}, \
- { K50, K51, K52, KC_NO, K54, K55, KC_NO, KC_NO}, \
- { KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO}, \
- { K70 , K71, K72, K73, K74, K75, K76, K77}, \
- { K80, K81, K82, K83, K84, K85, K86, K87}, \
- { K90, K91, K92, K93, K94, K95, K96, K97}, \
- { K100, K101, K102, K103, K104, K105, KC_NO, K107}, \
- { K110, K111, K112, K113, K114, K115, K116, K117}, \
- { K120, K121, K122, K123, KC_NO, KC_NO, K126, K127}, \
- { KC_NO, KC_NO, K132, K133, K134, K135, K136, K137} \
- }
-
-#endif
\ No newline at end of file
+++ /dev/null
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include "config_common.h"
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID 0xFEED
-#define PRODUCT_ID 0x3060
-#define DEVICE_VER 0x0001
-#define MANUFACTURER xyxjj
-#define PRODUCT DeltaSplit75
-#define DESCRIPTION 75% split keyboard
-
-/* key matrix size */
-// Rows are doubled-up
-#define MATRIX_ROWS 14
-#define MATRIX_COLS 8
-
-// wiring of each half
-#define MATRIX_ROW_PINS { F4, F5, F6, F7, B1, B3, B2 }
-#define MATRIX_COL_PINS { B6, B5, B4, E6, D7, C6, D4, D1}
-
-#define CATERINA_BOOTLOADER
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
-/* define if matrix has ghost */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-// #define BACKLIGHT_LEVELS 3
-
-/* Set 0 if debouncing isn't needed */
-#define DEBOUNCING_DELAY 5
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
-
-/* key combination for command */
-#define IS_COMMAND() ( \
- keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)
-
-/* ws2812 RGB LED */
-#define RGB_DI_PIN D3
-#define RGBLIGHT_TIMER
-#define RGBLED_NUM 12 // Number of LEDs
-#define ws2812_PORTREG PORTD
-#define ws2812_DDRREG DDRD
-
-/*
- * Feature disable options
- * These options are also useful to firmware size reduction.
- */
-
-/* disable debug print */
-// #define NO_DEBUG
-
-/* disable print */
-// #define NO_PRINT
-
-/* disable action features */
-//#define NO_ACTION_LAYER
-//#define NO_ACTION_TAPPING
-//#define NO_ACTION_ONESHOT
-//#define NO_ACTION_MACRO
-//#define NO_ACTION_FUNCTION
-
-
-#endif
\ No newline at end of file
+++ /dev/null
-BACKLIGHT_ENABLE = no
-
-ifndef QUANTUM_DIR
- include ../../../Makefile
-endif
+++ /dev/null
-ifndef MAKEFILE_INCLUDED
- include ../../Makefile
-endif
\ No newline at end of file
+++ /dev/null
-#include "deltasplit75.h"
-
-#ifdef AUDIO_ENABLE
- float tone_startup[][2] = SONG(STARTUP_SOUND);
- float tone_goodbye[][2] = SONG(GOODBYE_SOUND);
-#endif
-
-void matrix_init_kb(void) {
-
- #ifdef AUDIO_ENABLE
- _delay_ms(20); // gets rid of tick
- PLAY_NOTE_ARRAY(tone_startup, false, 0);
- #endif
-
- // // green led on
- // DDRD |= (1<<5);
- // PORTD &= ~(1<<5);
-
- // // orange led on
- // DDRB |= (1<<0);
- // PORTB &= ~(1<<0);
-
- matrix_init_user();
-};
-
-void shutdown_user(void) {
- #ifdef AUDIO_ENABLE
- PLAY_NOTE_ARRAY(tone_goodbye, false, 0);
- _delay_ms(150);
- stop_all_notes();
- #endif
-}
+++ /dev/null
-#ifndef v2_H
-#define v2_H
-
-#include "../deltasplit75.h"
-
-//void promicro_bootloader_jmp(bool program);
-#include "quantum.h"
-
-//void promicro_bootloader_jmp(bool program);
-//matrix is defined in a weird way here; the layout on both sides are asymmetrical, but the "matrix" is symmetrical but with empty gaps
-//the last column is defined as a separate row because the firmware currently doesnt support more than 8 columns (this layout has 9 columns per side) K45 and K110 are the Bs on both sides; K53 and K106 are extra keys for ISO
-#define KEYMAP( \
- K00, K01, K02, K03, K04, K05, K06, K70, K71, K72, K73, K74, K75, K76, K77, K132, \
- K10, K11, K12, K13, K14, K15, K16, K80, K81, K82, K83, K84, K85, K86, K87, K133, \
- K20, K21, K22, K23, K24, K25, K90, K91, K92, K93, K94, K95, K96, K97, K134, \
- K30, K31, K32, K33, K34, K35, K100, K101, K102, K103, K104, K105, K106, K107, K135, \
- K40, K53, K41, K42, K43, K44, K45, K110, K111, K112, K113, K114, K115, K116, K117, K136, \
- K50, K51, K52, K54, K55, K120, K121, K122, K123, K126, K127, K137 \
- ) \
- { \
- { K00, K01, K02, K03, K04, K05, K06, KC_NO}, \
- { K10, K11, K12, K13, K14, K15, K16, KC_NO}, \
- { K20, K21, K22, K23, K24, K25, KC_NO, KC_NO}, \
- { K30, K31, K32, K33, K34, K35, KC_NO, KC_NO}, \
- { K40, K41, K42, K43, K44, K45, KC_NO, KC_NO}, \
- { K50, K51, K52, K53, K54, K55, KC_NO, KC_NO}, \
- { KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO}, \
- { K70 , K71, K72, K73, K74, K75, K76, K77}, \
- { K80, K81, K82, K83, K84, K85, K86, K87}, \
- { K90, K91, K92, K93, K94, K95, K96, K97}, \
- { K100, K101, K102, K103, K104, K105, K106, K107}, \
- { K110, K111, K112, K113, K114, K115, K116, K117}, \
- { K120, K121, K122, K123, KC_NO, KC_NO, K126, K127}, \
- { KC_NO, KC_NO, K132, K133, K134, K135, K136, K137} \
- }
-
-#endif
\ No newline at end of file
+++ /dev/null
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include "config_common.h"
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID 0xFEED
-#define PRODUCT_ID 0x3060
-#define DEVICE_VER 0x0001
-#define MANUFACTURER xyxjj
-#define PRODUCT DeltaSplit75
-#define DESCRIPTION 75% split keyboard
-
-/* key matrix size */
-// Rows are doubled-up
-#define MATRIX_ROWS 14
-#define MATRIX_COLS 8
-
-// wiring of each half
-#define MATRIX_ROW_PINS { F4, F5, F6, F7, B1, B3, B2 }
-#define MATRIX_COL_PINS { B6, B5, B4, E6, D7, C6, D4, D1}
-
-#define CATERINA_BOOTLOADER
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
-/* define if matrix has ghost */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-// #define BACKLIGHT_LEVELS 3
-
-/* Set 0 if debouncing isn't needed */
-#define DEBOUNCING_DELAY 5
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
-
-/* key combination for command */
-#define IS_COMMAND() ( \
- keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)
-
-/* ws2812 RGB LED */
-#define RGB_DI_PIN D3
-#define RGBLIGHT_TIMER
-#define RGBLED_NUM 12 // Number of LEDs
-#define ws2812_PORTREG PORTD
-#define ws2812_DDRREG DDRD
-
-/*
- * Feature disable options
- * These options are also useful to firmware size reduction.
- */
-
-/* disable debug print */
-// #define NO_DEBUG
-
-/* disable print */
-// #define NO_PRINT
-
-/* disable action features */
-//#define NO_ACTION_LAYER
-//#define NO_ACTION_TAPPING
-//#define NO_ACTION_ONESHOT
-//#define NO_ACTION_MACRO
-//#define NO_ACTION_FUNCTION
-
-
-#endif
\ No newline at end of file
+++ /dev/null
-BACKLIGHT_ENABLE = no
-
-ifndef QUANTUM_DIR
- include ../../../Makefile
-endif
+++ /dev/null
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include "config_common.h"
-
-#ifdef SUBPROJECT_RightB
- #include "RightB/config.h"
-#endif
-#ifdef SUBPROJECT_V2
- #include "v2/config.h"
-#endif
-#endif
+++ /dev/null
-:0B0000000000000000000000000001F4\r
-:00000001FF\r
+++ /dev/null
-:0B0000000000000000000000000000F5\r
-:00000001FF\r
+++ /dev/null
-#include <util/twi.h>
-#include <avr/io.h>
-#include <stdlib.h>
-#include <avr/interrupt.h>
-#include <util/twi.h>
-#include <stdbool.h>
-#include "i2c.h"
-
-#ifdef USE_I2C
-
-// Limits the amount of we wait for any one i2c transaction.
-// Since were running SCL line 100kHz (=> 10μs/bit), and each transactions is
-// 9 bits, a single transaction will take around 90μs to complete.
-//
-// (F_CPU/SCL_CLOCK) => # of μC cycles to transfer a bit
-// poll loop takes at least 8 clock cycles to execute
-#define I2C_LOOP_TIMEOUT (9+1)*(F_CPU/SCL_CLOCK)/8
-
-#define BUFFER_POS_INC() (slave_buffer_pos = (slave_buffer_pos+1)%SLAVE_BUFFER_SIZE)
-
-volatile uint8_t i2c_slave_buffer[SLAVE_BUFFER_SIZE];
-
-static volatile uint8_t slave_buffer_pos;
-static volatile bool slave_has_register_set = false;
-
-// Wait for an i2c operation to finish
-inline static
-void i2c_delay(void) {
- uint16_t lim = 0;
- while(!(TWCR & (1<<TWINT)) && lim < I2C_LOOP_TIMEOUT)
- lim++;
-
- // easier way, but will wait slightly longer
- // _delay_us(100);
-}
-
-// Setup twi to run at 100kHz
-void i2c_master_init(void) {
- // no prescaler
- TWSR = 0;
- // Set TWI clock frequency to SCL_CLOCK. Need TWBR>10.
- // Check datasheets for more info.
- TWBR = ((F_CPU/SCL_CLOCK)-16)/2;
-}
-
-// Start a transaction with the given i2c slave address. The direction of the
-// transfer is set with I2C_READ and I2C_WRITE.
-// returns: 0 => success
-// 1 => error
-uint8_t i2c_master_start(uint8_t address) {
- TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTA);
-
- i2c_delay();
-
- // check that we started successfully
- if ( (TW_STATUS != TW_START) && (TW_STATUS != TW_REP_START))
- return 1;
-
- TWDR = address;
- TWCR = (1<<TWINT) | (1<<TWEN);
-
- i2c_delay();
-
- if ( (TW_STATUS != TW_MT_SLA_ACK) && (TW_STATUS != TW_MR_SLA_ACK) )
- return 1; // slave did not acknowledge
- else
- return 0; // success
-}
-
-
-// Finish the i2c transaction.
-void i2c_master_stop(void) {
- TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
-
- uint16_t lim = 0;
- while(!(TWCR & (1<<TWSTO)) && lim < I2C_LOOP_TIMEOUT)
- lim++;
-}
-
-// Write one byte to the i2c slave.
-// returns 0 => slave ACK
-// 1 => slave NACK
-uint8_t i2c_master_write(uint8_t data) {
- TWDR = data;
- TWCR = (1<<TWINT) | (1<<TWEN);
-
- i2c_delay();
-
- // check if the slave acknowledged us
- return (TW_STATUS == TW_MT_DATA_ACK) ? 0 : 1;
-}
-
-// Read one byte from the i2c slave. If ack=1 the slave is acknowledged,
-// if ack=0 the acknowledge bit is not set.
-// returns: byte read from i2c device
-uint8_t i2c_master_read(int ack) {
- TWCR = (1<<TWINT) | (1<<TWEN) | (ack<<TWEA);
-
- i2c_delay();
- return TWDR;
-}
-
-void i2c_reset_state(void) {
- TWCR = 0;
-}
-
-void i2c_slave_init(uint8_t address) {
- TWAR = address << 0; // slave i2c address
- // TWEN - twi enable
- // TWEA - enable address acknowledgement
- // TWINT - twi interrupt flag
- // TWIE - enable the twi interrupt
- TWCR = (1<<TWIE) | (1<<TWEA) | (1<<TWINT) | (1<<TWEN);
-}
-
-ISR(TWI_vect);
-
-ISR(TWI_vect) {
- uint8_t ack = 1;
- switch(TW_STATUS) {
- case TW_SR_SLA_ACK:
- // this device has been addressed as a slave receiver
- slave_has_register_set = false;
- break;
-
- case TW_SR_DATA_ACK:
- // this device has received data as a slave receiver
- // The first byte that we receive in this transaction sets the location
- // of the read/write location of the slaves memory that it exposes over
- // i2c. After that, bytes will be written at slave_buffer_pos, incrementing
- // slave_buffer_pos after each write.
- if(!slave_has_register_set) {
- slave_buffer_pos = TWDR;
- // don't acknowledge the master if this memory loctaion is out of bounds
- if ( slave_buffer_pos >= SLAVE_BUFFER_SIZE ) {
- ack = 0;
- slave_buffer_pos = 0;
- }
- slave_has_register_set = true;
- } else {
- i2c_slave_buffer[slave_buffer_pos] = TWDR;
- BUFFER_POS_INC();
- }
- break;
-
- case TW_ST_SLA_ACK:
- case TW_ST_DATA_ACK:
- // master has addressed this device as a slave transmitter and is
- // requesting data.
- TWDR = i2c_slave_buffer[slave_buffer_pos];
- BUFFER_POS_INC();
- break;
-
- case TW_BUS_ERROR: // something went wrong, reset twi state
- TWCR = 0;
- default:
- break;
- }
- // Reset everything, so we are ready for the next TWI interrupt
- TWCR |= (1<<TWIE) | (1<<TWINT) | (ack<<TWEA) | (1<<TWEN);
-}
-#endif
+++ /dev/null
-#ifndef I2C_H
-#define I2C_H
-
-#include <stdint.h>
-
-#ifndef F_CPU
-#define F_CPU 16000000UL
-#endif
-
-#define I2C_READ 1
-#define I2C_WRITE 0
-
-#define I2C_ACK 1
-#define I2C_NACK 0
-
-#define SLAVE_BUFFER_SIZE 0x10
-
-// i2c SCL clock frequency
-#define SCL_CLOCK 100000L
-
-extern volatile uint8_t i2c_slave_buffer[SLAVE_BUFFER_SIZE];
-
-void i2c_master_init(void);
-uint8_t i2c_master_start(uint8_t address);
-void i2c_master_stop(void);
-uint8_t i2c_master_write(uint8_t data);
-uint8_t i2c_master_read(int);
-void i2c_reset_state(void);
-void i2c_slave_init(uint8_t address);
-
-#endif
+++ /dev/null
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-
-#define USE_SERIAL
-
-#define MASTER_LEFT
-// #define _MASTER_RIGHT
-// #define EE_HANDS
-
-
-#ifdef SUBPROJECT_v2
- #include "../../v2/config.h"
-#endif
-#ifdef SUBPROJECT_ProtoSplit
- #include "../../ProtoSplit/config.h"
-#endif
+++ /dev/null
-#include "deltasplit75.h"
-#include "action_layer.h"
-#include "eeconfig.h"
-
-extern keymap_config_t keymap_config;
-
-// Each layer gets a name for readability, which is then used in the keymap matrix below.
-// The underscores don't mean anything - you can have a layer called STUFF or any other name.
-// Layer names don't all need to be of the same length, obviously, and you can also skip them
-// entirely and just use numbers.
-
-// Fillers to make layering more clear
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
- KEYMAP(
- KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_HOME, KC_PGUP,
- KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_DEL, KC_END, KC_PGDN,
- KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, KC_SLCK,
- KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_TRNS, KC_ENT, KC_PAUS, //modify KC_TRNS to enable ISO Support
- KC_LSFT, KC_TRNS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_LSFT, KC_UP, KC_PSCR, //modify KC_TRNS to enable ISO Support
- KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, MO(1), KC_SPC, KC_RALT, KC_RGUI, KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT),
-
- KEYMAP(
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET,
- KC_BSLS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- KC_TRNS, KC_VOLU, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- M(1), KC_LEFT, KC_DOWN, KC_RGHT, KC_PAUS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- KC_TRNS, KC_TRNS, KC_VOLD, M(0), KC_PSCR, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
-
-};
\ No newline at end of file
+++ /dev/null
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-
-#define USE_SERIAL
-
-#define MASTER_LEFT
-// #define _MASTER_RIGHT
-// #define EE_HANDS
-
-
-#ifdef SUBPROJECT_V2
- #include "../../V2/config.h"
-#endif
-#ifdef SUBPROJECT_ProtoSplit
- #include "../../ProtoSplit/config.h"
-#endif
+++ /dev/null
-#include "DeltaSplit75.h"
-#include "action_layer.h"
-#include "eeconfig.h"
-
-extern keymap_config_t keymap_config;
-
-// Each layer gets a name for readability, which is then used in the keymap matrix below.
-// The underscores don't mean anything - you can have a layer called STUFF or any other name.
-// Layer names don't all need to be of the same length, obviously, and you can also skip them
-// entirely and just use numbers.
-
-// Fillers to make layering more clear
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
- KEYMAP(
- KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_HOME, KC_PGUP,
- KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_DEL, KC_END, KC_PGDN,
- KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, KC_SLCK,
- KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, KC_PAUS,
- KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_LSFT, KC_UP, KC_PSCR,
- KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, MO(1), KC_SPC, KC_RALT, KC_RGUI, KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT),
-
- KEYMAP(
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET,
- KC_BSLS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- KC_TRNS, KC_VOLU, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- M(1), KC_LEFT, KC_DOWN, KC_RGHT, KC_PAUS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- KC_TRNS, KC_VOLD, M(0), KC_PSCR, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
-
-};
\ No newline at end of file
+++ /dev/null
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program. If not, see <http://www.gnu.org/licenses/>.
-*/
-
-/*
- * scan matrix
- */
-#include <stdint.h>
-#include <stdbool.h>
-#include <avr/io.h>
-#include <avr/wdt.h>
-#include <avr/interrupt.h>
-#include <util/delay.h>
-#include "print.h"
-#include "debug.h"
-#include "util.h"
-#include "matrix.h"
-#include "split_util.h"
-#include "pro_micro.h"
-#include "config.h"
-
-#ifdef USE_I2C
-# include "i2c.h"
-#else // USE_SERIAL
-# include "serial.h"
-#endif
-
-#ifndef DEBOUNCE
-# define DEBOUNCE 5
-#endif
-
-#define ERROR_DISCONNECT_COUNT 5
-
-static uint8_t debouncing = DEBOUNCE;
-static const int ROWS_PER_HAND = MATRIX_ROWS/2;
-static uint8_t error_count = 0;
-
-static const uint8_t row_pins[MATRIX_ROWS] = MATRIX_ROW_PINS;
-static const uint8_t col_pins[MATRIX_COLS] = MATRIX_COL_PINS;
-
-/* matrix state(1:on, 0:off) */
-static matrix_row_t matrix[MATRIX_ROWS];
-static matrix_row_t matrix_debouncing[MATRIX_ROWS];
-
-static matrix_row_t read_cols(void);
-static void init_cols(void);
-static void unselect_rows(void);
-static void select_row(uint8_t row);
-
-__attribute__ ((weak))
-void matrix_init_quantum(void) {
- matrix_init_kb();
-}
-
-__attribute__ ((weak))
-void matrix_scan_quantum(void) {
- matrix_scan_kb();
-}
-
-__attribute__ ((weak))
-void matrix_init_kb(void) {
- matrix_init_user();
-}
-
-__attribute__ ((weak))
-void matrix_scan_kb(void) {
- matrix_scan_user();
-}
-
-__attribute__ ((weak))
-void matrix_init_user(void) {
-}
-
-__attribute__ ((weak))
-void matrix_scan_user(void) {
-}
-
-inline
-uint8_t matrix_rows(void)
-{
- return MATRIX_ROWS;
-}
-
-inline
-uint8_t matrix_cols(void)
-{
- return MATRIX_COLS;
-}
-
-void matrix_init(void)
-{
- debug_enable = true;
- debug_matrix = true;
- debug_mouse = true;
- // initialize row and col
- unselect_rows();
- init_cols();
-
- TX_RX_LED_INIT;
-
- // initialize matrix state: all keys off
- for (uint8_t i=0; i < MATRIX_ROWS; i++) {
- matrix[i] = 0;
- matrix_debouncing[i] = 0;
- }
-
- matrix_init_quantum();
-}
-
-uint8_t _matrix_scan(void)
-{
- // Right hand is stored after the left in the matirx so, we need to offset it
- int offset = isLeftHand ? 0 : (ROWS_PER_HAND);
-
- for (uint8_t i = 0; i < ROWS_PER_HAND; i++) {
- select_row(i);
- _delay_us(30); // without this wait read unstable value.
- matrix_row_t cols = read_cols();
- if (matrix_debouncing[i+offset] != cols) {
- matrix_debouncing[i+offset] = cols;
- debouncing = DEBOUNCE;
- }
- unselect_rows();
- }
-
- if (debouncing) {
- if (--debouncing) {
- _delay_ms(1);
- } else {
- for (uint8_t i = 0; i < ROWS_PER_HAND; i++) {
- matrix[i+offset] = matrix_debouncing[i+offset];
- }
- }
- }
-
- return 1;
-}
-
-#ifdef USE_I2C
-
-// Get rows from other half over i2c
-int i2c_transaction(void) {
- int slaveOffset = (isLeftHand) ? (ROWS_PER_HAND) : 0;
-
- int err = i2c_master_start(SLAVE_I2C_ADDRESS + I2C_WRITE);
- if (err) goto i2c_error;
-
- // start of matrix stored at 0x00
- err = i2c_master_write(0x00);
- if (err) goto i2c_error;
-
- // Start read
- err = i2c_master_start(SLAVE_I2C_ADDRESS + I2C_READ);
- if (err) goto i2c_error;
-
- if (!err) {
- int i;
- for (i = 0; i < ROWS_PER_HAND-1; ++i) {
- matrix[slaveOffset+i] = i2c_master_read(I2C_ACK);
- }
- matrix[slaveOffset+i] = i2c_master_read(I2C_NACK);
- i2c_master_stop();
- } else {
-i2c_error: // the cable is disconnceted, or something else went wrong
- i2c_reset_state();
- return err;
- }
-
- return 0;
-}
-
-#else // USE_SERIAL
-
-int serial_transaction(void) {
- int slaveOffset = (isLeftHand) ? (ROWS_PER_HAND) : 0;
-
- if (serial_update_buffers()) {
- return 1;
- }
-
- for (int i = 0; i < ROWS_PER_HAND; ++i) {
- matrix[slaveOffset+i] = serial_slave_buffer[i];
- }
- return 0;
-}
-#endif
-
-uint8_t matrix_scan(void)
-{
- int ret = _matrix_scan();
-
-
-
-#ifdef USE_I2C
- if( i2c_transaction() ) {
-#else // USE_SERIAL
- if( serial_transaction() ) {
-#endif
- // turn on the indicator led when halves are disconnected
- TXLED1;
-
- error_count++;
-
- if (error_count > ERROR_DISCONNECT_COUNT) {
- // reset other half if disconnected
- int slaveOffset = (isLeftHand) ? (ROWS_PER_HAND) : 0;
- for (int i = 0; i < ROWS_PER_HAND; ++i) {
- matrix[slaveOffset+i] = 0;
- }
- }
- } else {
- // turn off the indicator led on no error
- TXLED0;
- error_count = 0;
- }
-
- matrix_scan_quantum();
-
- return ret;
-}
-
-void matrix_slave_scan(void) {
- _matrix_scan();
-
- int offset = (isLeftHand) ? 0 : (MATRIX_ROWS / 2);
-
-#ifdef USE_I2C
- for (int i = 0; i < ROWS_PER_HAND; ++i) {
- /* i2c_slave_buffer[i] = matrix[offset+i]; */
- i2c_slave_buffer[i] = matrix[offset+i];
- }
-#else // USE_SERIAL
- for (int i = 0; i < ROWS_PER_HAND; ++i) {
- serial_slave_buffer[i] = matrix[offset+i];
- }
-#endif
-}
-
-bool matrix_is_modified(void)
-{
- if (debouncing) return false;
- return true;
-}
-
-inline
-bool matrix_is_on(uint8_t row, uint8_t col)
-{
- return (matrix[row] & ((matrix_row_t)1<<col));
-}
-
-inline
-matrix_row_t matrix_get_row(uint8_t row)
-{
- return matrix[row];
-}
-
-void matrix_print(void)
-{
- print("\nr/c 0123456789ABCDEF\n");
- for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
- phex(row); print(": ");
- pbin_reverse16(matrix_get_row(row));
- print("\n");
- }
-}
-
-uint8_t matrix_key_count(void)
-{
- uint8_t count = 0;
- for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
- count += bitpop16(matrix[i]);
- }
- return count;
-}
-
-static void init_cols(void)
-{
- for(int x = 0; x < MATRIX_COLS; x++) {
- _SFR_IO8((col_pins[x] >> 4) + 1) &= ~_BV(col_pins[x] & 0xF);
- _SFR_IO8((col_pins[x] >> 4) + 2) |= _BV(col_pins[x] & 0xF);
- }
-}
-
-static matrix_row_t read_cols(void)
-{
- matrix_row_t result = 0;
- for(int x = 0; x < MATRIX_COLS; x++) {
- result |= (_SFR_IO8(col_pins[x] >> 4) & _BV(col_pins[x] & 0xF)) ? 0 : (1 << x);
- }
- return result;
-}
-
-static void unselect_rows(void)
-{
- for(int x = 0; x < ROWS_PER_HAND; x++) {
- _SFR_IO8((row_pins[x] >> 4) + 1) &= ~_BV(row_pins[x] & 0xF);
- _SFR_IO8((row_pins[x] >> 4) + 2) |= _BV(row_pins[x] & 0xF);
- }
-}
-
-static void select_row(uint8_t row)
-{
- _SFR_IO8((row_pins[row] >> 4) + 1) |= _BV(row_pins[row] & 0xF);
- _SFR_IO8((row_pins[row] >> 4) + 2) &= ~_BV(row_pins[row] & 0xF);
-}
+++ /dev/null
-/*
- pins_arduino.h - Pin definition functions for Arduino
- Part of Arduino - http://www.arduino.cc/
-
- Copyright (c) 2007 David A. Mellis
-
- This library is free software; you can redistribute it and/or
- modify it under the terms of the GNU Lesser General Public
- License as published by the Free Software Foundation; either
- version 2.1 of the License, or (at your option) any later version.
-
- This library is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- Lesser General Public License for more details.
-
- You should have received a copy of the GNU Lesser General
- Public License along with this library; if not, write to the
- Free Software Foundation, Inc., 59 Temple Place, Suite 330,
- Boston, MA 02111-1307 USA
-
- $Id: wiring.h 249 2007-02-03 16:52:51Z mellis $
-*/
-
-#ifndef Pins_Arduino_h
-#define Pins_Arduino_h
-
-#include <avr/pgmspace.h>
-
-// Workaround for wrong definitions in "iom32u4.h".
-// This should be fixed in the AVR toolchain.
-#undef UHCON
-#undef UHINT
-#undef UHIEN
-#undef UHADDR
-#undef UHFNUM
-#undef UHFNUML
-#undef UHFNUMH
-#undef UHFLEN
-#undef UPINRQX
-#undef UPINTX
-#undef UPNUM
-#undef UPRST
-#undef UPCONX
-#undef UPCFG0X
-#undef UPCFG1X
-#undef UPSTAX
-#undef UPCFG2X
-#undef UPIENX
-#undef UPDATX
-#undef TCCR2A
-#undef WGM20
-#undef WGM21
-#undef COM2B0
-#undef COM2B1
-#undef COM2A0
-#undef COM2A1
-#undef TCCR2B
-#undef CS20
-#undef CS21
-#undef CS22
-#undef WGM22
-#undef FOC2B
-#undef FOC2A
-#undef TCNT2
-#undef TCNT2_0
-#undef TCNT2_1
-#undef TCNT2_2
-#undef TCNT2_3
-#undef TCNT2_4
-#undef TCNT2_5
-#undef TCNT2_6
-#undef TCNT2_7
-#undef OCR2A
-#undef OCR2_0
-#undef OCR2_1
-#undef OCR2_2
-#undef OCR2_3
-#undef OCR2_4
-#undef OCR2_5
-#undef OCR2_6
-#undef OCR2_7
-#undef OCR2B
-#undef OCR2_0
-#undef OCR2_1
-#undef OCR2_2
-#undef OCR2_3
-#undef OCR2_4
-#undef OCR2_5
-#undef OCR2_6
-#undef OCR2_7
-
-#define NUM_DIGITAL_PINS 30
-#define NUM_ANALOG_INPUTS 12
-
-#define TX_RX_LED_INIT DDRD |= (1<<5), DDRB |= (1<<0)
-#define TXLED0 PORTD |= (1<<5)
-#define TXLED1 PORTD &= ~(1<<5)
-#define RXLED0 PORTB |= (1<<0)
-#define RXLED1 PORTB &= ~(1<<0)
-
-static const uint8_t SDA = 2;
-static const uint8_t SCL = 3;
-#define LED_BUILTIN 13
-
-// Map SPI port to 'new' pins D14..D17
-static const uint8_t SS = 17;
-static const uint8_t MOSI = 16;
-static const uint8_t MISO = 14;
-static const uint8_t SCK = 15;
-
-// Mapping of analog pins as digital I/O
-// A6-A11 share with digital pins
-static const uint8_t ADC0 = 18;
-static const uint8_t ADC1 = 19;
-static const uint8_t ADC2 = 20;
-static const uint8_t ADC3 = 21;
-static const uint8_t ADC4 = 22;
-static const uint8_t ADC5 = 23;
-static const uint8_t ADC6 = 24; // D4
-static const uint8_t ADC7 = 25; // D6
-static const uint8_t ADC8 = 26; // D8
-static const uint8_t ADC9 = 27; // D9
-static const uint8_t ADC10 = 28; // D10
-static const uint8_t ADC11 = 29; // D12
-
-#define digitalPinToPCICR(p) ((((p) >= 8 && (p) <= 11) || ((p) >= 14 && (p) <= 17) || ((p) >= A8 && (p) <= A10)) ? (&PCICR) : ((uint8_t *)0))
-#define digitalPinToPCICRbit(p) 0
-#define digitalPinToPCMSK(p) ((((p) >= 8 && (p) <= 11) || ((p) >= 14 && (p) <= 17) || ((p) >= A8 && (p) <= A10)) ? (&PCMSK0) : ((uint8_t *)0))
-#define digitalPinToPCMSKbit(p) ( ((p) >= 8 && (p) <= 11) ? (p) - 4 : ((p) == 14 ? 3 : ((p) == 15 ? 1 : ((p) == 16 ? 2 : ((p) == 17 ? 0 : (p - A8 + 4))))))
-
-// __AVR_ATmega32U4__ has an unusual mapping of pins to channels
-extern const uint8_t PROGMEM analog_pin_to_channel_PGM[];
-#define analogPinToChannel(P) ( pgm_read_byte( analog_pin_to_channel_PGM + (P) ) )
-
-#define digitalPinToInterrupt(p) ((p) == 0 ? 2 : ((p) == 1 ? 3 : ((p) == 2 ? 1 : ((p) == 3 ? 0 : ((p) == 7 ? 4 : NOT_AN_INTERRUPT)))))
-
-#ifdef ARDUINO_MAIN
-
-// On the Arduino board, digital pins are also used
-// for the analog output (software PWM). Analog input
-// pins are a separate set.
-
-// ATMEL ATMEGA32U4 / ARDUINO LEONARDO
-//
-// D0 PD2 RXD1/INT2
-// D1 PD3 TXD1/INT3
-// D2 PD1 SDA SDA/INT1
-// D3# PD0 PWM8/SCL OC0B/SCL/INT0
-// D4 A6 PD4 ADC8
-// D5# PC6 ??? OC3A/#OC4A
-// D6# A7 PD7 FastPWM #OC4D/ADC10
-// D7 PE6 INT6/AIN0
-//
-// D8 A8 PB4 ADC11/PCINT4
-// D9# A9 PB5 PWM16 OC1A/#OC4B/ADC12/PCINT5
-// D10# A10 PB6 PWM16 OC1B/0c4B/ADC13/PCINT6
-// D11# PB7 PWM8/16 0C0A/OC1C/#RTS/PCINT7
-// D12 A11 PD6 T1/#OC4D/ADC9
-// D13# PC7 PWM10 CLK0/OC4A
-//
-// A0 D18 PF7 ADC7
-// A1 D19 PF6 ADC6
-// A2 D20 PF5 ADC5
-// A3 D21 PF4 ADC4
-// A4 D22 PF1 ADC1
-// A5 D23 PF0 ADC0
-//
-// New pins D14..D17 to map SPI port to digital pins
-//
-// MISO D14 PB3 MISO,PCINT3
-// SCK D15 PB1 SCK,PCINT1
-// MOSI D16 PB2 MOSI,PCINT2
-// SS D17 PB0 RXLED,SS/PCINT0
-//
-// Connected LEDs on board for TX and RX
-// TXLED D24 PD5 XCK1
-// RXLED D17 PB0
-// HWB PE2 HWB
-
-// these arrays map port names (e.g. port B) to the
-// appropriate addresses for various functions (e.g. reading
-// and writing)
-const uint16_t PROGMEM port_to_mode_PGM[] = {
- NOT_A_PORT,
- NOT_A_PORT,
- (uint16_t) &DDRB,
- (uint16_t) &DDRC,
- (uint16_t) &DDRD,
- (uint16_t) &DDRE,
- (uint16_t) &DDRF,
-};
-
-const uint16_t PROGMEM port_to_output_PGM[] = {
- NOT_A_PORT,
- NOT_A_PORT,
- (uint16_t) &PORTB,
- (uint16_t) &PORTC,
- (uint16_t) &PORTD,
- (uint16_t) &PORTE,
- (uint16_t) &PORTF,
-};
-
-const uint16_t PROGMEM port_to_input_PGM[] = {
- NOT_A_PORT,
- NOT_A_PORT,
- (uint16_t) &PINB,
- (uint16_t) &PINC,
- (uint16_t) &PIND,
- (uint16_t) &PINE,
- (uint16_t) &PINF,
-};
-
-const uint8_t PROGMEM digital_pin_to_port_PGM[] = {
- PD, // D0 - PD2
- PD, // D1 - PD3
- PD, // D2 - PD1
- PD, // D3 - PD0
- PD, // D4 - PD4
- PC, // D5 - PC6
- PD, // D6 - PD7
- PE, // D7 - PE6
-
- PB, // D8 - PB4
- PB, // D9 - PB5
- PB, // D10 - PB6
- PB, // D11 - PB7
- PD, // D12 - PD6
- PC, // D13 - PC7
-
- PB, // D14 - MISO - PB3
- PB, // D15 - SCK - PB1
- PB, // D16 - MOSI - PB2
- PB, // D17 - SS - PB0
-
- PF, // D18 - A0 - PF7
- PF, // D19 - A1 - PF6
- PF, // D20 - A2 - PF5
- PF, // D21 - A3 - PF4
- PF, // D22 - A4 - PF1
- PF, // D23 - A5 - PF0
-
- PD, // D24 - PD5
- PD, // D25 / D6 - A7 - PD7
- PB, // D26 / D8 - A8 - PB4
- PB, // D27 / D9 - A9 - PB5
- PB, // D28 / D10 - A10 - PB6
- PD, // D29 / D12 - A11 - PD6
-};
-
-const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = {
- _BV(2), // D0 - PD2
- _BV(3), // D1 - PD3
- _BV(1), // D2 - PD1
- _BV(0), // D3 - PD0
- _BV(4), // D4 - PD4
- _BV(6), // D5 - PC6
- _BV(7), // D6 - PD7
- _BV(6), // D7 - PE6
-
- _BV(4), // D8 - PB4
- _BV(5), // D9 - PB5
- _BV(6), // D10 - PB6
- _BV(7), // D11 - PB7
- _BV(6), // D12 - PD6
- _BV(7), // D13 - PC7
-
- _BV(3), // D14 - MISO - PB3
- _BV(1), // D15 - SCK - PB1
- _BV(2), // D16 - MOSI - PB2
- _BV(0), // D17 - SS - PB0
-
- _BV(7), // D18 - A0 - PF7
- _BV(6), // D19 - A1 - PF6
- _BV(5), // D20 - A2 - PF5
- _BV(4), // D21 - A3 - PF4
- _BV(1), // D22 - A4 - PF1
- _BV(0), // D23 - A5 - PF0
-
- _BV(5), // D24 - PD5
- _BV(7), // D25 / D6 - A7 - PD7
- _BV(4), // D26 / D8 - A8 - PB4
- _BV(5), // D27 / D9 - A9 - PB5
- _BV(6), // D28 / D10 - A10 - PB6
- _BV(6), // D29 / D12 - A11 - PD6
-};
-
-const uint8_t PROGMEM digital_pin_to_timer_PGM[] = {
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- TIMER0B, /* 3 */
- NOT_ON_TIMER,
- TIMER3A, /* 5 */
- TIMER4D, /* 6 */
- NOT_ON_TIMER,
-
- NOT_ON_TIMER,
- TIMER1A, /* 9 */
- TIMER1B, /* 10 */
- TIMER0A, /* 11 */
-
- NOT_ON_TIMER,
- TIMER4A, /* 13 */
-
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
-
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
- NOT_ON_TIMER,
-};
-
-const uint8_t PROGMEM analog_pin_to_channel_PGM[] = {
- 7, // A0 PF7 ADC7
- 6, // A1 PF6 ADC6
- 5, // A2 PF5 ADC5
- 4, // A3 PF4 ADC4
- 1, // A4 PF1 ADC1
- 0, // A5 PF0 ADC0
- 8, // A6 D4 PD4 ADC8
- 10, // A7 D6 PD7 ADC10
- 11, // A8 D8 PB4 ADC11
- 12, // A9 D9 PB5 ADC12
- 13, // A10 D10 PB6 ADC13
- 9 // A11 D12 PD6 ADC9
-};
-
-#endif /* ARDUINO_MAIN */
-
-// These serial port names are intended to allow libraries and architecture-neutral
-// sketches to automatically default to the correct port name for a particular type
-// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
-// the first hardware serial port whose RX/TX pins are not dedicated to another use.
-//
-// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
-//
-// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
-//
-// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
-//
-// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
-//
-// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
-// pins are NOT connected to anything by default.
-#define SERIAL_PORT_MONITOR Serial
-#define SERIAL_PORT_USBVIRTUAL Serial
-#define SERIAL_PORT_HARDWARE Serial1
-#define SERIAL_PORT_HARDWARE_OPEN Serial1
-
-#endif /* Pins_Arduino_h */
+++ /dev/null
-DeltaSplit75
-======
-
-This readme and most of the code are from https://github.com/ahtn/tmk_keyboard/ and https://github.com/qmk/qmk_firmware/tree/master/keyboards/lets_split
-
-Credit to ahtn and wootpatoot for work on the split keyboard firmware
-
-Split keyboard firmware for Arduino Pro Micro or other ATmega32u4
-based boards.
-
-## Case Files
-Files are available here: https://github.com/xyxjj/DeltaSplit75-Case-files
-
-
-## First Time Setup
-
-Download or clone the whole firmware and navigate to the keyboards/DeltaSplit75 directory. Once your dev env is setup, you'll be able to generate the default .hex using:
-
-```
-make V2
-
-or
-
-make ProtoSplit-ProtoSplit (if you have one of the prototype PCBs)
-```
-
-You will see a lot of output and if everything worked correctly you will see the built hex files:
-
-```
-DeltaSplit75_ProtoSplit_ProtoSplit.hex
-
-or
-
-DeltaSplit75_V2_Default.hex
-
-```
-
-
-For more information on customizing keymaps, take a look at the primary documentation for [Customizing Your Keymap](/readme.md##customizing-your-keymap) in the main readme.md.
-
-### DeltaSplit75 V2
-The PCBs available in groupbuy are all v2, if you've bought one of my prototype PCBs (it says DeltaSplit65 on the silkscreen instead of 75), use the code make ProtoSplit-ProtoSplit instead
-
-Features
---------
-
-For the full Quantum Mechanical Keyboard feature list, see [the parent readme.md](/readme.md).
-
-Some features supported by the firmware:
-
-* Either half can connect to the computer via USB, or both halves can be used
- independently.
-* 75% formfactor
-* Support for multiple Bottom Rows
-* RGB underglow support
-* Split Backspace and ISO support
-
-
-Flashing
--------
-I personally use xLoader to upload my hex files to the keyboard, though any other working software is fine too
-
-
-Choosing which board to plug the USB cable into (choosing Master)
---------
-Because the two boards are identical, the firmware has logic to differentiate the left and right board.
-
-It uses two strategies to figure things out: look at the EEPROM (memory on the chip) or looks if the current board has the usb cable.
-
-The EEPROM approach requires additional setup (flashing the eeeprom) but allows you to swap the usb cable to either side.
-
-The USB cable approach is easier to setup and if you just want the usb cable on the left board, you do not need to do anything extra.
-
-### Setting the left hand as master
-If you always plug the usb cable into the left board, nothing extra is needed as this is the default. Comment out `EE_HANDS` and comment out `I2C_MASTER_RIGHT` or `MASTER_RIGHT` if for some reason it was set.
-
-### Setting the right hand as master
-If you always plug the usb cable into the right board, add an extra flag to your `config.h`
-```
- #define MASTER_RIGHT
-```
-
-### Setting EE_hands to use either hands as master
-If you define `EE_HANDS` in your `config.h`, you will need to set the
-EEPROM for the left and right halves.
-
-The EEPROM is used to store whether the
-half is left handed or right handed. This makes it so that the same firmware
-file will run on both hands instead of having to flash left and right handed
-versions of the firmware to each half. To flash the EEPROM file for the left
-half run:
-```
-avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-lefthand.eep
-// or the equivalent in dfu-programmer
-
-```
-and similarly for right half
-```
-avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-righhand.eep
-// or the equivalent in dfu-programmer
-```
-
-NOTE: replace `$(COM_PORT)` with the port of your device (e.g. `/dev/ttyACM0`)
-
-After you have flashed the EEPROM, you then need to set `EE_HANDS` in your config.h, rebuild the hex files and reflash.
-
-Note that you need to program both halves, but you have the option of using
-different keymaps for each half. You could program the left half with a QWERTY
-layout and the right half with a Colemak layout using bootmagic's default layout option.
-Then if you connect the left half to a computer by USB the keyboard will use QWERTY and Colemak when the
-right half is connected.
-
-
-Notes on Using Pro Micro 3.3V
------------------------------
-
-Do update the `F_CPU` parameter in `rules.mk` to `8000000` which reflects
-the frequency on the 3.3V board.
-
-Also, if the slave board is producing weird characters in certain columns,
-update the following line in `matrix.c` to the following:
-
-```
-// _delay_us(30); // without this wait read unstable value.
-_delay_us(300); // without this wait read unstable value.
-```
+++ /dev/null
-SRC += matrix.c \
- i2c.c \
- split_util.c \
- serial.c
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-CONSOLE_ENABLE ?= no # Console for debug(+400)
-COMMAND_ENABLE ?= yes # Commands for debug and configuration
-NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality
-MIDI_ENABLE ?= no # MIDI controls
-AUDIO_ENABLE ?= no # Audio output on port C6
-UNICODE_ENABLE ?= no # Unicode
-BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
-SUBPROJECT_rev1 ?= yes
-USE_I2C ?= yes
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
-
-CUSTOM_MATRIX = yes
-
-avrdude: build
- ls /dev/tty* > /tmp/1; \
- echo "Reset your Pro Micro now"; \
- while [[ -z $$USB ]]; do \
- sleep 1; \
- ls /dev/tty* > /tmp/2; \
- USB=`diff /tmp/1 /tmp/2 | grep -o '/dev/tty.*'`; \
- done; \
- avrdude -p $(MCU) -c avr109 -P $$USB -U flash:w:$(BUILD_DIR)/$(TARGET).hex
-
-.PHONY: avrdude
+++ /dev/null
-/*
- * WARNING: be careful changing this code, it is very timing dependent
- */
-
-#ifndef F_CPU
-#define F_CPU 16000000
-#endif
-
-#include <avr/io.h>
-#include <avr/interrupt.h>
-#include <util/delay.h>
-#include <stdbool.h>
-#include "serial.h"
-
-#ifdef USE_SERIAL
-
-// Serial pulse period in microseconds. Its probably a bad idea to lower this
-// value.
-#define SERIAL_DELAY 24
-
-uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0};
-uint8_t volatile serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH] = {0};
-
-#define SLAVE_DATA_CORRUPT (1<<0)
-volatile uint8_t status = 0;
-
-inline static
-void serial_delay(void) {
- _delay_us(SERIAL_DELAY);
-}
-
-inline static
-void serial_output(void) {
- SERIAL_PIN_DDR |= SERIAL_PIN_MASK;
-}
-
-// make the serial pin an input with pull-up resistor
-inline static
-void serial_input(void) {
- SERIAL_PIN_DDR &= ~SERIAL_PIN_MASK;
- SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
-}
-
-inline static
-uint8_t serial_read_pin(void) {
- return !!(SERIAL_PIN_INPUT & SERIAL_PIN_MASK);
-}
-
-inline static
-void serial_low(void) {
- SERIAL_PIN_PORT &= ~SERIAL_PIN_MASK;
-}
-
-inline static
-void serial_high(void) {
- SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
-}
-
-void serial_master_init(void) {
- serial_output();
- serial_high();
-}
-
-void serial_slave_init(void) {
- serial_input();
-
- // Enable INT0
- EIMSK |= _BV(INT0);
- // Trigger on falling edge of INT0
- EICRA &= ~(_BV(ISC00) | _BV(ISC01));
-}
-
-// Used by the master to synchronize timing with the slave.
-static
-void sync_recv(void) {
- serial_input();
- // This shouldn't hang if the slave disconnects because the
- // serial line will float to high if the slave does disconnect.
- while (!serial_read_pin());
- serial_delay();
-}
-
-// Used by the slave to send a synchronization signal to the master.
-static
-void sync_send(void) {
- serial_output();
-
- serial_low();
- serial_delay();
-
- serial_high();
-}
-
-// Reads a byte from the serial line
-static
-uint8_t serial_read_byte(void) {
- uint8_t byte = 0;
- serial_input();
- for ( uint8_t i = 0; i < 8; ++i) {
- byte = (byte << 1) | serial_read_pin();
- serial_delay();
- _delay_us(1);
- }
-
- return byte;
-}
-
-// Sends a byte with MSB ordering
-static
-void serial_write_byte(uint8_t data) {
- uint8_t b = 8;
- serial_output();
- while( b-- ) {
- if(data & (1 << b)) {
- serial_high();
- } else {
- serial_low();
- }
- serial_delay();
- }
-}
-
-// interrupt handle to be used by the slave device
-ISR(SERIAL_PIN_INTERRUPT) {
- sync_send();
-
- uint8_t checksum = 0;
- for (int i = 0; i < SERIAL_SLAVE_BUFFER_LENGTH; ++i) {
- serial_write_byte(serial_slave_buffer[i]);
- sync_send();
- checksum += serial_slave_buffer[i];
- }
- serial_write_byte(checksum);
- sync_send();
-
- // wait for the sync to finish sending
- serial_delay();
-
- // read the middle of pulses
- _delay_us(SERIAL_DELAY/2);
-
- uint8_t checksum_computed = 0;
- for (int i = 0; i < SERIAL_MASTER_BUFFER_LENGTH; ++i) {
- serial_master_buffer[i] = serial_read_byte();
- sync_send();
- checksum_computed += serial_master_buffer[i];
- }
- uint8_t checksum_received = serial_read_byte();
- sync_send();
-
- serial_input(); // end transaction
-
- if ( checksum_computed != checksum_received ) {
- status |= SLAVE_DATA_CORRUPT;
- } else {
- status &= ~SLAVE_DATA_CORRUPT;
- }
-}
-
-inline
-bool serial_slave_DATA_CORRUPT(void) {
- return status & SLAVE_DATA_CORRUPT;
-}
-
-// Copies the serial_slave_buffer to the master and sends the
-// serial_master_buffer to the slave.
-//
-// Returns:
-// 0 => no error
-// 1 => slave did not respond
-int serial_update_buffers(void) {
- // this code is very time dependent, so we need to disable interrupts
- cli();
-
- // signal to the slave that we want to start a transaction
- serial_output();
- serial_low();
- _delay_us(1);
-
- // wait for the slaves response
- serial_input();
- serial_high();
- _delay_us(SERIAL_DELAY);
-
- // check if the slave is present
- if (serial_read_pin()) {
- // slave failed to pull the line low, assume not present
- sei();
- return 1;
- }
-
- // if the slave is present syncronize with it
- sync_recv();
-
- uint8_t checksum_computed = 0;
- // receive data from the slave
- for (int i = 0; i < SERIAL_SLAVE_BUFFER_LENGTH; ++i) {
- serial_slave_buffer[i] = serial_read_byte();
- sync_recv();
- checksum_computed += serial_slave_buffer[i];
- }
- uint8_t checksum_received = serial_read_byte();
- sync_recv();
-
- if (checksum_computed != checksum_received) {
- sei();
- return 1;
- }
-
- uint8_t checksum = 0;
- // send data to the slave
- for (int i = 0; i < SERIAL_MASTER_BUFFER_LENGTH; ++i) {
- serial_write_byte(serial_master_buffer[i]);
- sync_recv();
- checksum += serial_master_buffer[i];
- }
- serial_write_byte(checksum);
- sync_recv();
-
- // always, release the line when not in use
- serial_output();
- serial_high();
-
- sei();
- return 0;
-}
-
-#endif
+++ /dev/null
-#ifndef MY_SERIAL_H
-#define MY_SERIAL_H
-
-#include "config.h"
-#include <stdbool.h>
-
-/* TODO: some defines for interrupt setup */
-#define SERIAL_PIN_DDR DDRD
-#define SERIAL_PIN_PORT PORTD
-#define SERIAL_PIN_INPUT PIND
-#define SERIAL_PIN_MASK _BV(PD0)
-#define SERIAL_PIN_INTERRUPT INT0_vect
-
-#define SERIAL_SLAVE_BUFFER_LENGTH ((MATRIX_COLS+7)/8 *MATRIX_ROWS/2)
-#define SERIAL_MASTER_BUFFER_LENGTH 1
-
-// Buffers for master - slave communication
-extern volatile uint8_t serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH];
-extern volatile uint8_t serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH];
-
-void serial_master_init(void);
-void serial_slave_init(void);
-int serial_update_buffers(void);
-bool serial_slave_data_corrupt(void);
-
-#endif
+++ /dev/null
-#include <avr/io.h>
-#include <avr/wdt.h>
-#include <avr/power.h>
-#include <avr/interrupt.h>
-#include <util/delay.h>
-#include <avr/eeprom.h>
-#include "split_util.h"
-#include "matrix.h"
-#include "keyboard.h"
-#include "config.h"
-
-#ifdef USE_I2C
-# include "i2c.h"
-#else
-# include "serial.h"
-#endif
-
-volatile bool isLeftHand = true;
-
-static void setup_handedness(void) {
- #ifdef EE_HANDS
- isLeftHand = eeprom_read_byte(EECONFIG_HANDEDNESS);
- #else
- // I2C_MASTER_RIGHT is deprecated use MASTER_RIGHT instead since this works for both serial and i2c
- #if defined(I2C_MASTER_RIGHT) || defined(MASTER_RIGHT)
- isLeftHand = !has_usb();
- #else
- isLeftHand = has_usb();
- #endif
- #endif
-}
-
-static void keyboard_master_setup(void) {
-#ifdef USE_I2C
- i2c_master_init();
-#else
- serial_master_init();
-#endif
-}
-
-static void keyboard_slave_setup(void) {
-#ifdef USE_I2C
- i2c_slave_init(SLAVE_I2C_ADDRESS);
-#else
- serial_slave_init();
-#endif
-}
-
-bool has_usb(void) {
- USBCON |= (1 << OTGPADE); //enables VBUS pad
- _delay_us(5);
- return (USBSTA & (1<<VBUS)); //checks state of VBUS
-}
-
-void split_keyboard_setup(void) {
- setup_handedness();
-
- if (has_usb()) {
- keyboard_master_setup();
- } else {
- keyboard_slave_setup();
- }
- sei();
-}
-
-void keyboard_slave_loop(void) {
- matrix_init();
-
- while (1) {
- matrix_slave_scan();
- }
-}
-
-// this code runs before the usb and keyboard is initialized
-void matrix_setup(void) {
- split_keyboard_setup();
-
- if (!has_usb()) {
- keyboard_slave_loop();
- }
-}
+++ /dev/null
-#ifndef SPLIT_KEYBOARD_UTIL_H
-#define SPLIT_KEYBOARD_UTIL_H
-
-#include <stdbool.h>
-
-#ifdef EE_HANDS
- #define EECONFIG_BOOTMAGIC_END (uint8_t *)10
- #define EECONFIG_HANDEDNESS EECONFIG_BOOTMAGIC_END
-#endif
-
-#define SLAVE_I2C_ADDRESS 0x32
-
-extern volatile bool isLeftHand;
-
-// slave version of matix scan, defined in matrix.c
-void matrix_slave_scan(void);
-
-void split_keyboard_setup(void);
-bool has_usb(void);
-void keyboard_slave_loop(void);
-
-#endif
projects / qmk_firmware.git / commitdiff