--- /dev/null
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6060
+#define DEVICE_VER 0x0001
+#define MANUFACTURER YMDK
+#define PRODUCT YD60MQ
+#define DESCRIPTION Keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 15
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }
+#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, F7, B5, B4, D7, D6, B3, B2 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* number of backlight levels */
+#define BACKLIGHT_PIN B7
+#ifdef BACKLIGHT_PIN
+#define BACKLIGHT_LEVELS 5
+#endif
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* prevent stuck modifiers */
+
+#define RGB_DI_PIN E2
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 12
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#endif
+
--- /dev/null
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+ LAYOUT(
+ KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV,
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
+ KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_BSLS, KC_ENT,
+ KC_LSFT, KC_NUHS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, KC_DEL,
+ KC_LCTL, KC_LGUI, KC_LALT, MO(1), KC_SPC, MO(1), KC_RALT, KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT),
+
+ LAYOUT(
+ RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_DEL,
+ KC_TRNS, RGB_TOG, KC_UP, RGB_MOD, RGB_HUI, RGB_HUD, RGB_SAI, RGB_SAD, RGB_VAI, RGB_VAD, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, BL_DEC, BL_TOGG, BL_INC, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+};
+
+void matrix_init_user(void) {
+}
+
+void matrix_scan_user(void) {
+}
--- /dev/null
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+ LAYOUT(
+ KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV,
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC,
+ KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_BSLS, KC_ENT,
+ KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, _______, KC_RSFT, MO(1),
+ KC_LCTL, KC_LALT, KC_LGUI, _______, KC_SPC, _______, _______, KC_RALT, _______, KC_RGUI, KC_RCTL),
+
+ LAYOUT(
+ KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL,
+ KC_CAPS, RGB_TOG, RGB_MOD, RGB_HUI, RGB_VAD, RGB_VAI, RGB_SAD, RGB_SAI, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, _______, RESET,
+ _______, KC_VOLD, KC_VOLU, KC_MUTE, _______, _______, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT, _______, _______,
+ _______, KC_NO, _______, _______, _______, _______, _______, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______)
+
+};
--- /dev/null
+YD60MQ
+======
+
+
+
+Customizable 60% PCB by [YMDK](https://ymdk.aliexpress.com/store/429151?spm=2114.10010108.0.0.3ab23641lIkgzm).
+
+Keyboard Maintainer: QMK Community
+Hardware Supported: YD60MQ
+Hardware Availability: YMDK - [AliExpress](https://www.aliexpress.com/item/YMDK-60-YD60MQ-QMK-Programmable-Underglow-RGB-Led-PCB-Plate-Stabilizers-For-DIY-Mechanical-Keyboard-Interchange/32869207240.html)
+
+Make example for this keyboard (after setting up your build environment):
+
+ make yd60mq:default
+
+The keyboard uses a DFU bootloader. To make a keymap and use dfu-util to flash it:
+
+ make yd60mq:default:dfu
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information.
--- /dev/null
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# atmega32a bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# Build Options
+# comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
+AUDIO_ENABLE = no
+RGBLIGHT_ENABLE = yes
--- /dev/null
+#include "yd60mq.h"
+
+void led_set_kb(uint8_t usb_led) {
+ if (IS_LED_ON(usb_led, USB_LED_CAPS_LOCK)) {
+ setPinOutput(F4);
+ writePinLow(F4);
+ } else {
+ setPinInput(F4);
+ writePinLow(F4);
+ }
+
+ led_set_user(usb_led);
+}
--- /dev/null
+#pragma once
+
+#include "quantum.h"
+
+#define LAYOUT( \
+ K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, \
+ K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \
+ K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, \
+ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314, \
+ K400, K401, K402, K403, K407, K408, K409, K410, K411, K412, K413 \
+) { \
+ { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \
+ { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, KC_NO }, \
+ { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, KC_NO }, \
+ { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314 }, \
+ { K400, K401, K402, K403, KC_NO, KC_NO, KC_NO, K407, K408, K409, K410, K411, K412, K413, KC_NO } \
+}
+
projects / qmk_firmware.git / commitdiff