--- /dev/null
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6060
+#define DEVICE_VER 0x0001
+#define MANUFACTURER blindassassin111
+#define PRODUCT Z-150 PCB
+#define DESCRIPTION Replacement for Zenith Z-150 PCB
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 20
+
+/* key matrix pins */
+#define MATRIX_ROW_PINS { C3, C2, C1, C0, E1 }
+#define MATRIX_COL_PINS { D0, D1, D2, D3, D4, D5, D7, E0, C7, C6, C5, C4, F0, F1, F2, F3, F4, F5, F6, F7 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* force n-key rollover*/
+#define FORCE_NKRO
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* prevent stuck modifiers */
+#define PREVENT_STUCK_MODIFIERS
+
+
+#ifdef RGB_DI_PIN
+#define RGBLIGHT_ANIMATIONS
+#define RGBLED_NUM 0
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#endif
\ No newline at end of file
--- /dev/null
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+ LAYOUT(
+ KC_F1, KC_F2, KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_NLCK, KC_SLCK, MO(1),
+ KC_F3, KC_F4, KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_ENT, KC_P7, KC_P8, KC_P9, KC_PAST,
+ KC_F5, KC_F6, KC_LCTRL,KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_P4, KC_P5, KC_P6, KC_PMNS,
+ KC_F7, KC_F8, KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT,KC_SLSH, KC_RSFT, KC_BSLS, KC_P1, KC_P2, KC_P3, KC_PPLS,
+ KC_F9, KC_F10, KC_LALT, KC_GRV, KC_SPC, KC_CAPS, KC_P0, KC_PDOT
+ ),
+
+ LAYOUT(
+ _______, _______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______
+ ),
+
+ LAYOUT_z150_tkl(
+ KC_F1, KC_F2, KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_INS, KC_HOME, KC_PGUP,
+ KC_F3, KC_F4, KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_DEL, KC_END, KC_PGDN,
+ KC_F5, KC_F6, KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX,
+ KC_F7, KC_F8, KC_LSFT, KC_BSLS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, MO(1), XXXXXXX, KC_UP, XXXXXXX,
+ KC_F9, KC_F10, KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, KC_MENU, KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT
+ ),
+
+ LAYOUT_z150_tkl(
+ _______, _______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______
+ ),
+};
+
+void matrix_init_user(void) {
+}
+
+void matrix_scan_user(void) {
+}
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+ return true;
+}
+
+void led_set_user(uint8_t usb_led) {
+ DDRB |= (1 << 0);
+ DDRE |= (1 << 6) | (1 << 7);
+
+ if (usb_led & (1 << USB_LED_NUM_LOCK)) {
+ PORTE |= (1 << 7);
+ } else {
+ PORTE &= ~(1 << 7);
+ }
+
+ if (usb_led & (1 << USB_LED_CAPS_LOCK)) {
+ PORTB |= (1 << 0);
+ } else {
+ PORTB &= ~(1 << 0);
+ }
+
+ if (usb_led & (1 << USB_LED_SCROLL_LOCK)) {
+ PORTE |= (1 << 6);
+ } else {
+ PORTE &= ~(1 << 6);
+ }
+}
\ No newline at end of file
--- /dev/null
+Z-150 Blackheart PCB
+===
+
+A replacement PCB for Zenith Z-150 keyboards.
+
+Keyboard Maintainer: QMK Community and blindassassin111
+Hardware Supported: Z-150 blackheart PCB
+Hardware Availability: https://deskthority.net/group-buys-f50/programmable-vintage-board-pcbs-omnikey-at101-and-z-150-t19325.html
+
+Make example for this keyboard (after setting up your build environment):
+
+ make z150_blackheart:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
--- /dev/null
+# MCU name
+MCU = at90usb1286
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Bootloader selection
+BOOTLOADER = halfkay
+
+# Boot Section Size in *bytes*
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
+AUDIO_ENABLE = no
+RGBLIGHT_ENABLE = no
\ No newline at end of file
--- /dev/null
+#include "z150_blackheart.h"
--- /dev/null
+#ifndef z150_blackheart_H
+#define z150_blackheart_H
+
+#include "quantum.h"
+
+#define LAYOUT( \
+ K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, K015, K016, K017, K019, \
+ K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115, K116, K117, K118, K119, \
+ K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K215, K216, K217, K218, \
+ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314, K315, K316, K317, K318, \
+ K400, K401, K402, K403, K407, K414, K415, K417 \
+) { \
+ { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, K015, K016, K017, KC_NO, K019 }, \
+ { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115, K116, K117, K118, K119 }, \
+ { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, KC_NO, K215, K216, K217, K218, KC_NO }, \
+ { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314, K315, K316, K317, K318, KC_NO }, \
+ { K400, K401, K402, K403, KC_NO, KC_NO, KC_NO, K407, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, K414, K415, KC_NO, K417, KC_NO, KC_NO } \
+}
+
+#define LAYOUT_z150_tkl( \
+ K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, K015, K017, K018, K019, \
+ K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115, K117, K118, K119, \
+ K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, K216, K217, K218, \
+ K300, K301, K302, K405, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314, K316, K317, K318, \
+ K400, K401, K402, K403, K404, K407, K412, K413, K414, K415, K416, K417, K418 \
+) { \
+ { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014, K015, KC_NO, K017, K018, K019 }, \
+ { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115, KC_NO, K117, K118, K119 }, \
+ { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, KC_NO, K216, K217, K218, KC_NO }, \
+ { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314, KC_NO, K316, K317, K318, KC_NO }, \
+ { K400, K401, K402, K403, K404, K405, KC_NO, K407, KC_NO, KC_NO, KC_NO, KC_NO, K412, K413, K414, K415, K416, K417, K418, KC_NO } \
+}
+
+#endif
\ No newline at end of file
projects / qmk_firmware.git / commitdiff