--- /dev/null
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+# Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+# (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+# have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+# have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+# (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+# (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+# with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+# bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = hhkb_qmk
+
+
+# Directory common source filess exist
+TOP_DIR = ../..
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# # project specific files
+SRC = hhkb_qmk.c \
+ matrix.c
+
+ifdef KEYMAP
+ SRC := keymaps/keymap_$(KEYMAP).c $(SRC)
+else
+ SRC := keymaps/keymap_default.c $(SRC)
+endif
+
+CONFIG_H = config.h
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+#OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# as per original hasu settings
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+# Build Options
+# comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+CUSTOM_MATRIX = yes # Custom matrix file for the HHKB
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
+# NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
+# MIDI_ENABLE = YES # MIDI controls
+# UNICODE_ENABLE = YES # Unicode
+# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
+
+
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+VPATH += $(TMK_DIR)
+
+debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
+debug-on: all
+
+debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
+debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
+debug-off: all
+
+include $(TOP_DIR)/quantum/quantum.mk
--- /dev/null
+hhkb_qmk keyboard firmware
+======================
+
+## Quantum MK Firmware
+
+You have access to a bunch of goodies! Check out the Makefile to enable/disable some of the features. Uncomment the `#` to enable them. Setting them to `no` does nothing and will only confuse future you.
+
+ BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
+ MIDI_ENABLE = yes # MIDI controls
+ # UNICODE_ENABLE = yes # Unicode support - this is commented out, just as an example. You have to use #, not //
+ BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
+
+## Quick aliases to common actions
+
+Your keymap can include shortcuts to common operations (called "function actions" in tmk).
+
+### Switching and toggling layers
+
+`MO(layer)` - momentary switch to *layer*. As soon as you let go of the key, the layer is deactivated and you pop back out to the previous layer. When you apply this to a key, that same key must be set as `KC_TRNS` on the destination layer. Otherwise, you won't make it back to the original layer when you release the key (and you'll get a keycode sent). You can only switch to layers *above* your current layer. If you're on layer 0 and you use `MO(1)`, that will switch to layer 1 just fine. But if you include `MO(3)` on layer 5, that won't do anything for you -- because layer 3 is lower than layer 5 on the stack.
+
+`LT(layer, kc)` - momentary switch to *layer* when held, and *kc* when tapped. Like `MO()`, this only works upwards in the layer stack (`layer` must be higher than the current layer).
+
+`TG(layer)` - toggles a layer on or off. As with `MO()`, you should set this key as `KC_TRNS` in the destination layer so that tapping it again actually toggles back to the original layer. Only works upwards in the layer stack.
+
+### Fun with modifier keys
+
+* `LSFT(kc)` - applies left Shift to *kc* (keycode) - `S(kc)` is an alias
+* `RSFT(kc)` - applies right Shift to *kc*
+* `LCTL(kc)` - applies left Control to *kc*
+* `RCTL(kc)` - applies right Control to *kc*
+* `LALT(kc)` - applies left Alt to *kc*
+* `RALT(kc)` - applies right Alt to *kc*
+* `LGUI(kc)` - applies left GUI (command/win) to *kc*
+* `RGUI(kc)` - applies right GUI (command/win) to *kc*
+
+You can also chain these, like this:
+
+ LALT(LCTL(KC_DEL)) -- this makes a key that sends Alt, Control, and Delete in a single keypress.
+
+The following shortcuts automatically add `LSFT()` to keycodes to get commonly used symbols. Their long names are also available and documented in `/quantum/keymap_common.h`.
+
+ KC_TILD ~
+ KC_EXLM !
+ KC_AT @
+ KC_HASH #
+ KC_DLR $
+ KC_PERC %
+ KC_CIRC ^
+ KC_AMPR &
+ KC_ASTR *
+ KC_LPRN (
+ KC_RPRN )
+ KC_UNDS _
+ KC_PLUS +
+ KC_LCBR {
+ KC_RCBR }
+ KC_PIPE |
+ KC_COLN :
+
+`MT(mod, kc)` - is *mod* (modifier key - MOD_LCTL, MOD_LSFT) when held, and *kc* when tapped. In other words, you can have a key that sends Esc (or the letter O or whatever) when you tap it, but works as a Control key or a Shift key when you hold it down.
+
+These are the values you can use for the `mod` in `MT()` (right-hand modifiers are not available):
+
+ * MOD_LCTL
+ * MOD_LSFT
+ * MOD_LALT
+ * MOD_LGUI
+
+These can also be combined like `MOD_LCTL | MOD_LSFT` e.g. `MT(MOD_LCTL | MOD_LSFT, KC_ESC)` which would activate Control and Shift when held, and send Escape when tapped.
+
+We've added shortcuts to make common modifier/tap (mod-tap) mappings more compact:
+
+ * `CTL_T(kc)` - is LCTL when held and *kc* when tapped
+ * `SFT_T(kc)` - is LSFT when held and *kc* when tapped
+ * `ALT_T(kc)` - is LALT when held and *kc* when tapped
+ * `GUI_T(kc)` - is LGUI when held and *kc* when tapped
+ * `ALL_T(kc)` - is Hyper (all mods) when held and *kc* when tapped. To read more about what you can do with a Hyper key, see [this blog post by Brett Terpstra](http://brettterpstra.com/2012/12/08/a-useful-caps-lock-key/)
+
+### Temporarily setting the default layer
+
+`DF(layer)` - sets default layer to *layer*. The default layer is the one at the "bottom" of the layer stack - the ultimate fallback layer. This currently does not persist over power loss. When you plug the keyboard back in, layer 0 will always be the default. It is theoretically possible to work around that, but that's not what `DF` does.
+
+### Remember: These are just aliases
+
+These functions work the same way that their `ACTION_*` functions do - they're just quick aliases. To dig into all of the tmk ACTION_* functions, please see the [TMK documentation](https://github.com/jackhumbert/qmk_firmware/blob/master/tmk_core/doc/keymap.md#2-action).
+
+Instead of using `FNx` when defining `ACTION_*` functions, you can use `F(x)` - the benefit here is being able to use more than 32 function actions (up to 4096), if you happen to need them.
+
+## Macro shortcuts: Send a whole string when pressing just one key
+
+Instead of using the `ACTION_MACRO` function, you can simply use `M(n)` to access macro *n* - *n* will get passed into the `action_get_macro` as the `id`, and you can use a switch statement to trigger it. This gets called on the keydown and keyup, so you'll need to use an if statement testing `record->event.pressed` (see keymap_default.c).
+
+```c
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) // this is the function signature -- just copy/paste it into your keymap file as it is.
+{
+ switch(id) {
+ case 0: // this would trigger when you hit a key mapped as M(0)
+ if (record->event.pressed) {
+ return MACRO( I(255), T(H), T(E), T(L), T(L), W(255), T(O), END ); // this sends the string 'hello' when the macro executes
+ }
+ break;
+ }
+ return MACRO_NONE;
+};
+```
+A macro can include the following commands:
+
+* I() change interval of stroke in milliseconds.
+* D() press key.
+* U() release key.
+* T() type key(press and release).
+* W() wait (milliseconds).
+* END end mark.
+
+So above you can see the stroke interval changed to 255ms between each keystroke, then a bunch of keys being typed, waits a while, then the macro ends.
+
+Note: Using macros to have your keyboard send passwords for you is a bad idea.
+
+### Additional keycode aliases for software-implemented layouts (Colemak, Dvorak, etc)
+
+Everything is assuming you're in Qwerty (in software) by default, but there is built-in support for using a Colemak or Dvorak layout by including this at the top of your keymap:
+
+ #include "keymap_<layout>.h"
+
+Where <layout> is "colemak" or "dvorak". After including this line, you will get access to:
+
+ * `CM_*` for all of the Colemak-equivalent characters
+ * `DV_*` for all of the Dvorak-equivalent characters
+
+These implementations assume you're using Colemak or Dvorak on your OS, not on your keyboard - this is referred to as a software-implemented layout. If your computer is in Qwerty and your keymap is in Colemak or Dvorak, this is referred to as a firmware-implemented layout, and you won't need these features.
+
+To give an example, if you're using software-implemented Colemak, and want to get an `F`, you would use `CM_F` - `KC_F` under these same circumstances would result in `T`.
+
+## Additional language support
+
+In `quantum/keymap_extras/`, you'll see various language files - these work the same way as the alternative layout ones do. Most are defined by their two letter country/language code followed by an underscore and a 4-letter abbreviation of its name. `FR_UGRV` which will result in a `ù` when using a software-implemented AZERTY layout. It's currently difficult to send such characters in just the firmware (but it's being worked on - see Unicode support).
+
+## Unicode support
+
+You can currently send 4 hex digits with your OS-specific modifier key (RALT for OSX with the "Unicode Hex Input" layout) - this is currently limited to supporting one OS at a time, and requires a recompile for switching. 8 digit hex codes are being worked on. The keycode function is `UC(n)`, where *n* is a 4 digit hexidecimal. Enable from the Makefile.
+
+## Other firmware shortcut keycodes
+
+* `RESET` - puts the MCU in DFU mode for flashing new firmware (with `make dfu`)
+* `DEBUG` - the firmware into debug mode - you'll need hid_listen to see things
+* `BL_ON` - turns the backlight on
+* `BL_OFF` - turns the backlight off
+* `BL_<n>` - sets the backlight to level *n*
+* `BL_INC` - increments the backlight level by one
+* `BL_DEC` - decrements the backlight level by one
+* `BL_TOGG` - toggles the backlight
+* `BL_STEP` - steps through the backlight levels
+
+Enable the backlight from the Makefile.
+
+## MIDI functionalty
+
+This is still a WIP, but check out `quantum/keymap_midi.c` to see what's happening. Enable from the Makefile.
+
+## Bluetooth functionality
+
+This requires [some hardware changes](https://www.reddit.com/r/MechanicalKeyboards/comments/3psx0q/the_planck_keyboard_with_bluetooth_guide_and/?ref=search_posts), but can be enabled via the Makefile. The firmware will still output characters via USB, so be aware of this when charging via a computer. It would make sense to have a switch on the Bluefruit to turn it off at will.
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboard/planck folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use `make dfu` to program your PCB once you hit the reset button.
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document (you can find in top README.md) and existent keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+```
+$ make KEYMAP=[default|jack|<name>]
+```
+Keymaps follow the format **__keymap\_\<name\>.c__** and are stored in the `keymaps` folder.
--- /dev/null
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0xCAFE
+#define DEVICE_VER 0x0104
+#define MANUFACTURER q.m.k
+#define PRODUCT HHKB mod
+#define DESCRIPTION q.m.k keyboard firmware for HHKB
+
+/* key matrix size */
+#define MATRIX_ROWS 8
+#define MATRIX_COLS 8
+
+#define TAPPING_TERM 200
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCE 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+//#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+//#define LOCKING_RESYNC_ENABLE
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+*/
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
--- /dev/null
+#ifndef HHKB_AVR_H
+#define HHKB_AVR_H
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <avr/io.h>
+#include <avr/interrupt.h>
+#include <util/delay.h>
+
+
+// Timer resolution check
+#if (1000000/TIMER_RAW_FREQ > 20)
+# error "Timer resolution(>20us) is not enough for HHKB matrix scan tweak on V-USB."
+#endif
+
+
+/*
+ * HHKB Matrix I/O
+ *
+ * row: HC4051[A,B,C] selects scan row0-7
+ * row-ext: [En0,En1] row extention for JP
+ * col: LS145[A,B,C,D] selects scan col0-7 and enable(D)
+ * key: on: 0/off: 1
+ * prev: hysteresis control: assert(1) when previous key state is on
+ */
+
+
+#if defined(__AVR_ATmega32U4__)
+/*
+ * For TMK HHKB alt controller(ATMega32U4)
+ *
+ * row: PB0-2
+ * col: PB3-5,6
+ * key: PD7(pull-uped)
+ * prev: PB7
+ * power: PD4(L:off/H:on)
+ * row-ext: PC6,7 for HHKB JP(active low)
+ */
+static inline void KEY_ENABLE(void) { (PORTB &= ~(1<<6)); }
+static inline void KEY_UNABLE(void) { (PORTB |= (1<<6)); }
+static inline bool KEY_STATE(void) { return (PIND & (1<<7)); }
+static inline void KEY_PREV_ON(void) { (PORTB |= (1<<7)); }
+static inline void KEY_PREV_OFF(void) { (PORTB &= ~(1<<7)); }
+#ifdef HHKB_POWER_SAVING
+static inline void KEY_POWER_ON(void) {
+ DDRB = 0xFF; PORTB = 0x40; // change pins output
+ DDRD |= (1<<4); PORTD |= (1<<4); // MOS FET switch on
+ /* Without this wait you will miss or get false key events. */
+ _delay_ms(5); // wait for powering up
+}
+static inline void KEY_POWER_OFF(void) {
+ /* input with pull-up consumes less than without it when pin is open. */
+ DDRB = 0x00; PORTB = 0xFF; // change pins input with pull-up
+ DDRD |= (1<<4); PORTD &= ~(1<<4); // MOS FET switch off
+}
+static inline bool KEY_POWER_STATE(void) { return PORTD & (1<<4); }
+#else
+static inline void KEY_POWER_ON(void) {}
+static inline void KEY_POWER_OFF(void) {}
+static inline bool KEY_POWER_STATE(void) { return true; }
+#endif
+static inline void KEY_INIT(void)
+{
+ /* row,col,prev: output */
+ DDRB = 0xFF;
+ PORTB = 0x40; // unable
+ /* key: input with pull-up */
+ DDRD &= ~0x80;
+ PORTD |= 0x80;
+#ifdef HHKB_JP
+ /* row extention for HHKB JP */
+ DDRC |= (1<<6|1<<7);
+ PORTC |= (1<<6|1<<7);
+#endif
+ KEY_UNABLE();
+ KEY_PREV_OFF();
+
+ KEY_POWER_OFF();
+}
+static inline void KEY_SELECT(uint8_t ROW, uint8_t COL)
+{
+ PORTB = (PORTB & 0xC0) | (((COL) & 0x07)<<3) | ((ROW) & 0x07);
+#ifdef HHKB_JP
+ if ((ROW) & 0x08) PORTC = (PORTC & ~(1<<6|1<<7)) | (1<<6);
+ else PORTC = (PORTC & ~(1<<6|1<<7)) | (1<<7);
+#endif
+}
+
+
+#elif defined(__AVR_AT90USB1286__)
+/*
+ * For Teensy++(AT90USB1286)
+ *
+ * HHKB pro HHKB pro2
+ * row: PB0-2 (6-8) (5-7)
+ * col: PB3-5,6 (9-12) (8-11)
+ * key: PE6(pull-uped) (4) (3)
+ * prev: PE7 (5) (4)
+ *
+ * TODO: convert into 'staitc inline' function
+ */
+#define KEY_INIT() do { \
+ DDRB |= 0x7F; \
+ DDRE |= (1<<7); \
+ DDRE &= ~(1<<6); \
+ PORTE |= (1<<6); \
+} while (0)
+#define KEY_SELECT(ROW, COL) (PORTB = (PORTB & 0xC0) | \
+ (((COL) & 0x07)<<3) | \
+ ((ROW) & 0x07))
+#define KEY_ENABLE() (PORTB &= ~(1<<6))
+#define KEY_UNABLE() (PORTB |= (1<<6))
+#define KEY_STATE() (PINE & (1<<6))
+#define KEY_PREV_ON() (PORTE |= (1<<7))
+#define KEY_PREV_OFF() (PORTE &= ~(1<<7))
+#define KEY_POWER_ON()
+#define KEY_POWER_OFF()
+#define KEY_POWER_STATE() true
+
+
+#else
+# error "define code for matrix scan"
+#endif
+
+
+#if 0
+// For ATMega328P with V-USB
+//
+// #elif defined(__AVR_ATmega328P__)
+// Ports for V-USB
+// key: PB0(pull-uped)
+// prev: PB1
+// row: PB2-4
+// col: PC0-2,3
+// power: PB5(Low:on/Hi-z:off)
+#define KEY_INIT() do { \
+ DDRB |= 0x3E; \
+ DDRB &= ~(1<<0); \
+ PORTB |= 1<<0; \
+ DDRC |= 0x0F; \
+ KEY_UNABLE(); \
+ KEY_PREV_OFF(); \
+} while (0)
+#define KEY_SELECT(ROW, COL) do { \
+ PORTB = (PORTB & 0xE3) | ((ROW) & 0x07)<<2; \
+ PORTC = (PORTC & 0xF8) | ((COL) & 0x07); \
+} while (0)
+#define KEY_ENABLE() (PORTC &= ~(1<<3))
+#define KEY_UNABLE() (PORTC |= (1<<3))
+#define KEY_STATE() (PINB & (1<<0))
+#define KEY_PREV_ON() (PORTB |= (1<<1))
+#define KEY_PREV_OFF() (PORTB &= ~(1<<1))
+// Power supply switching
+#define KEY_POWER_ON() do { \
+ KEY_INIT(); \
+ PORTB &= ~(1<<5); \
+ _delay_ms(1); \
+} while (0)
+#define KEY_POWER_OFF() do { \
+ DDRB &= ~0x3F; \
+ PORTB &= ~0x3F; \
+ DDRC &= ~0x0F; \
+ PORTC &= ~0x0F; \
+} while (0)
+#endif
+
+#endif
--- /dev/null
+#include "hhkb_qmk.h"
+
+__attribute__ ((weak))
+void * matrix_init_user(void) {
+ // leave these blank
+};
+
+__attribute__ ((weak))
+void * matrix_scan_user(void) {
+ // leave these blank
+};
+
+void * matrix_init_kb(void) {
+ // put your keyboard start-up code here
+ // runs once when the firmware starts up
+
+ if (matrix_init_user) {
+ (*matrix_init_user)();
+ }
+};
+
+void * matrix_scan_kb(void) {
+ // put your looping keyboard code here
+ // runs every cycle (a lot)
+
+ if (matrix_scan_user) {
+ (*matrix_scan_user)();
+ }
+};
--- /dev/null
+#ifndef HHKB_QMK_H
+#define HHKB_QMK_H
+
+#include "matrix.h"
+#include "keymap_common.h"
+//#include "backlight.h"
+#include <stddef.h>
+
+#define KEYMAP( \
+ K31, K30, K00, K10, K11, K20, K21, K40, K41, K60, K61, K70, K71, K50, K51, \
+ K32, K01, K02, K13, K12, K23, K22, K42, K43, K62, K63, K73, K72, K52, \
+ K33, K04, K03, K14, K15, K24, K25, K45, K44, K65, K64, K74, K53, \
+ K34, K05, K06, K07, K16, K17, K26, K46, K66, K76, K75, K55, K54, \
+ K35, K36, K37, K57, K56) \
+ \
+{ \
+ { K00, K01, K02, K03, K04, K05, K06, K07 }, \
+ { K10, K11, K12, K13, K14, K15, K16, K17 }, \
+ { K20, K21, K22, K23, K24, K25, K26, KC_NO }, \
+ { K30, K31, K32, K33, K34, K35, K36, K37 }, \
+ { K40, K41, K42, K43, K44, K45, K46, KC_NO }, \
+ { K50, K51, K52, K53, K54, K55, K56, K57 }, \
+ { K60, K61, K62, K63, K64, K65, K66, KC_NO }, \
+ { K70, K71, K72, K73, K74, K75, K76, KC_NO } \
+}
+
+void * matrix_init_user(void);
+void * matrix_scan_user(void);
+
+#endif
--- /dev/null
+/* -*- eval: (turn-on-orgtbl); -*-
+ * default HHKB Layout
+ */
+#include "hhkb_qmk.h"
+
+#define BASE 0
+#define HHKB 1
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+ /* BASE Level: Default Layer
+ |-------+---+---+---+---+---+---+---+---+---+---+-------+-----+-------+---|
+ | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` |
+ |-------+---+---+---+---+---+---+---+---+---+---+-------+-----+-------+---|
+ | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Backs | |
+ |-------+---+---+---+---+---+---+---+---+---+---+-------+-----+-------+---|
+ | Cont | A | S | D | F | G | H | J | K | L | ; | ' | Ent | | |
+ |-------+---+---+---+---+---+---+---+---+---+---+-------+-----+-------+---|
+ | Shift | Z | X | C | V | B | N | M | , | . | / | Shift | Fn0 | | |
+ |-------+---+---+---+---+---+---+---+---+---+---+-------+-----+-------+---|
+
+ |------+------+-----------------------+------+------|
+ | LAlt | LGUI | ******* Space ******* | RGUI | RAlt |
+ |------+------+-----------------------+------+------|
+ */
+
+ [BASE] = KEYMAP( // default layer
+ KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, \
+ KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(HHKB), \
+ KC_LALT, KC_LGUI, /* */ KC_SPC, KC_RGUI, KC_RALT),
+
+
+
+ /* Layer HHKB: HHKB mode (HHKB Fn)
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+ | Pwr | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | Ins | Del |
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+ | Caps | | | | | | | | Psc | Slk | Pus | Up | | Backs | |
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+ | | VoD | VoU | Mut | | | * | / | Hom | PgU | Lef | Rig | Enter | | |
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+ | | | | | | | + | - | End | PgD | Dow | | | | |
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+
+ |------+------+----------------------+------+------+
+ | **** | **** | ******************** | **** | **** |
+ |------+------+----------------------+------+------+
+
+ */
+
+ [HHKB] = KEYMAP(
+ KC_PWR, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, \
+ KC_CAPS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, KC_TRNS, KC_BSPC, \
+ KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_TRNS, KC_TRNS, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT, KC_PENT, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, KC_TRNS, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS)};
+
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+ // MACRODOWN only works in this function
+ switch(id) {
+ case 0:
+ if (record->event.pressed) {
+ register_code(KC_RSFT);
+ } else {
+ unregister_code(KC_RSFT);
+ }
+ break;
+ }
+ return MACRO_NONE;
+};
--- /dev/null
+/* -*- eval: (turn-on-orgtbl); -*-
+ * lxol HHKB Layout
+ */
+#include "hhkb_qmk.h"
+
+#define BASE 0
+#define WIN 1
+#define HHKB 2
+#define RGUILEV 3
+#define LGUILEV 4
+#define RALTLEV 5
+#define LALTLEV 6
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+ /* Layer 0: Default Layer
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Backs | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Contro | A | S | D | F | G | H | J | K | L | ; | ' | RCtl/Ent | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Shift | Z | X | C | V | B | N | M | , | . | Fn2 | Shift | Fn0 | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+
+ |------+------+-------+------+------|
+ | LAlt | LGUI | Space | RGUI | RAlt |
+ |------+------+-------+------+------|
+ */
+
+ [BASE] = KEYMAP( // layer 0 : default
+
+
+ KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, \
+ KC_LCTL, LT(LALTLEV,KC_A), LT(LGUILEV,KC_S), KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, LT(RGUILEV,KC_L), LT(RALTLEV,KC_SCLN), KC_QUOT, KC_FN0, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(HHKB), \
+ KC_LALT, KC_LGUI, KC_SPC, KC_RGUI, KC_RALT),
+
+
+
+ /* Layer 1: HHKB mode (HHKB Fn)
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+ | Pwr | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | Ins | Del |
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+ | Caps | | | | | | | | Psc | Slk | Pus | Up | | Backs | |
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+ | | VoD | VoU | Mut | | | * | / | Hom | PgU | Lef | Rig | Enter | | |
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+ | | | | | | | + | - | End | PgD | Dow | | | | |
+ |------+-----+-----+-----+----+----+----+----+-----+-----+-----+-----+-------+-------+-----|
+
+ |---+---+---+---+---|
+ | | | | | |
+ |---+---+---+---+---|
+ */
+
+ [HHKB] = KEYMAP(
+ KC_PWR, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, \
+ KC_CAPS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, KC_TRNS, KC_BSPC, \
+ KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_TRNS, KC_TRNS, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT, KC_PENT, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, KC_TRNS, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+
+ /* Layer LGUI: All keys with RGUI modifier
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Backs | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Contro | A | S | D | F | G | H | J | K | | ; | ' | RCtl/Ent | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Shift | Z | X | C | V | B | N | M | , | . | Fn2 | Shift | Fn0 | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+
+ |------+------+-------+------+------|
+ | LAlt | LGUI | Space | RGUI | RAlt |
+ |------+------+-------+------+------|
+ */
+
+ [RGUILEV] = KEYMAP( // Right GUI layer by KC_L
+
+ RGUI(KC_ESC), RGUI(KC_1), RGUI(KC_2), RGUI(KC_3), RGUI(KC_4), RGUI(KC_5), RGUI(KC_6), RGUI(KC_7), RGUI(KC_8), RGUI(KC_9), RGUI(KC_0), RGUI(KC_MINS), RGUI(KC_EQL), RGUI(KC_BSLS), RGUI(KC_GRV), \
+ RGUI(KC_TAB), RGUI(KC_Q), RGUI(KC_W), RGUI(KC_E), RGUI(KC_R), RGUI(KC_T), RGUI(KC_Y), RGUI(KC_U), RGUI(KC_I), RGUI(KC_O), RGUI(KC_P), RGUI(KC_LBRC), RGUI(KC_RBRC), RGUI(KC_BSPC), \
+ RGUI(KC_LCTL), RGUI(KC_A), RGUI(KC_S), RGUI(KC_D), RGUI(KC_F), RGUI(KC_G), RGUI(KC_H), RGUI(KC_J), RGUI(KC_K), KC_TRNS, KC_TRNS, RGUI(KC_QUOT), KC_FN0, \
+ RGUI(KC_LSFT), RGUI(KC_Z), RGUI(KC_X), RGUI(KC_C), RGUI(KC_V), RGUI(KC_B), RGUI(KC_N), RGUI(KC_M), RGUI(KC_COMM), RGUI(KC_DOT), RGUI(KC_SLSH), RGUI(KC_RSFT), KC_TRNS, \
+ KC_LALT, KC_LGUI, RGUI(KC_SPC), KC_RGUI, KC_RALT),
+
+ /* Layer LGUI: All keys with LGUI modifier
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Backs | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Contro | A | S | D | F | G | H | J | K | | ; | ' | RCtl/Ent | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Shift | Z | X | C | V | B | N | M | , | . | Fn2 | Shift | Fn0 | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+
+ |------+------+-------+------+------|
+ | LAlt | LGUI | Space | LGUI | RAlt |
+ |------+------+-------+------+------|
+ */
+
+ [LGUILEV] = KEYMAP( // Right GUI layer by KC_L
+
+ LGUI(KC_ESC), LGUI(KC_1), LGUI(KC_2), LGUI(KC_3), LGUI(KC_4), LGUI(KC_5), LGUI(KC_6), LGUI(KC_7), LGUI(KC_8), LGUI(KC_9), LGUI(KC_0), LGUI(KC_MINS), LGUI(KC_EQL), LGUI(KC_BSLS), LGUI(KC_GRV), \
+ LGUI(KC_TAB), LGUI(KC_Q), LGUI(KC_W), LGUI(KC_E), LGUI(KC_R), LGUI(KC_T), LGUI(KC_Y), LGUI(KC_U), LGUI(KC_I), LGUI(KC_O), LGUI(KC_P), LGUI(KC_LBRC), LGUI(KC_RBRC), LGUI(KC_BSPC), \
+ LGUI(KC_LCTL), KC_TRNS, KC_TRNS, LGUI(KC_D), LGUI(KC_F), LGUI(KC_G), LGUI(KC_H), LGUI(KC_J), LGUI(KC_K), LGUI(KC_L), LGUI(KC_SCLN), LGUI(KC_QUOT), KC_FN0, \
+ KC_LSFT, LGUI(KC_Z), LGUI(KC_X), LGUI(KC_C), LGUI(KC_V), LGUI(KC_B), LGUI(KC_N), LGUI(KC_M), LGUI(KC_COMM), LGUI(KC_DOT), LGUI(KC_SLSH), KC_RSFT, KC_TRNS, \
+ KC_LALT, KC_LGUI, LGUI(KC_SPC), KC_LGUI, KC_RALT),
+
+ /* Layer LALT: All keys with RALT modifier
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Backs | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Contro | A | S | D | F | G | H | J | K | | ; | ' | RCtl/Ent | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Shift | Z | X | C | V | B | N | M | , | . | Fn2 | Shift | Fn0 | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+
+ |------+------+-------+------+------|
+ | LAlt | LGUI | Space | RGUI | RAlt |
+ |------+------+-------+------+------|
+ */
+
+ [RALTLEV] = KEYMAP( // Right ALT layer by KC_L
+
+ RALT(KC_ESC), RALT(KC_1), RALT(KC_2), RALT(KC_3), RALT(KC_4), RALT(KC_5), RALT(KC_6), RALT(KC_7), RALT(KC_8), RALT(KC_9), RALT(KC_0), RALT(KC_MINS), RALT(KC_EQL), RALT(KC_BSLS), RALT(KC_GRV), \
+ RALT(KC_TAB), RALT(KC_Q), RALT(KC_W), RALT(KC_E), RALT(KC_R), RALT(KC_T), RALT(KC_Y), RALT(KC_U), RALT(KC_I), RALT(KC_O), RALT(KC_P), RALT(KC_LBRC), RALT(KC_RBRC), RALT(KC_BSPC), \
+ RALT(KC_LCTL), RALT(KC_A), RALT(KC_S), RALT(KC_D), RALT(KC_F), RALT(KC_G), RALT(KC_H), RALT(KC_J), RALT(KC_K), KC_TRNS, KC_TRNS, RALT(KC_QUOT), KC_FN0, \
+ RALT(KC_LSFT), RALT(KC_Z), RALT(KC_X), RALT(KC_C), RALT(KC_V), RALT(KC_B), RALT(KC_N), RALT(KC_M), RALT(KC_COMM), RALT(KC_DOT), RALT(KC_SLSH), RALT(KC_RSFT), KC_TRNS, \
+ KC_LALT, KC_LGUI, RALT(KC_SPC), KC_RGUI, KC_RALT),
+
+ /* Layer LALT: All keys with LALT modifier
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Backs | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Contro | A | S | D | F | G | H | J | K | | ; | ' | RCtl/Ent | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+ | Shift | Z | X | C | V | B | N | M | , | . | Fn2 | Shift | Fn0 | | |
+ |--------+---+---+---+---+---+---+---+---+---+-----+-------+----------+-------+---|
+
+ |------+------+-------+------+------|
+ | LAlt | LGUI | Space | LGUI | RAlt |
+ |------+------+-------+------+------|
+ */
+
+ [LALTLEV] = KEYMAP( // Right ALT layer by KC_L
+
+ LALT(KC_ESC), LALT(KC_1), LALT(KC_2), LALT(KC_3), LALT(KC_4), LALT(KC_5), LALT(KC_6), LALT(KC_7), LALT(KC_8), LALT(KC_9), LALT(KC_0), LALT(KC_MINS), LALT(KC_EQL), LALT(KC_BSLS), LALT(KC_GRV), \
+ LALT(KC_TAB), LALT(KC_Q), LALT(KC_W), LALT(KC_E), LALT(KC_R), LALT(KC_T), LALT(KC_Y), LALT(KC_U), LALT(KC_I), LALT(KC_O), LALT(KC_P), LALT(KC_LBRC), LALT(KC_RBRC), LALT(KC_BSPC), \
+ LALT(KC_LCTL), KC_TRNS, KC_TRNS, LALT(KC_D), LALT(KC_F), LALT(KC_G), LALT(KC_H), LALT(KC_J), LALT(KC_K), LALT(KC_L), LALT(KC_SCLN), LALT(KC_QUOT), KC_FN0, \
+ KC_LSFT, LALT(KC_Z), LALT(KC_X), LALT(KC_C), LALT(KC_V), LALT(KC_B), LALT(KC_N), LALT(KC_M), LALT(KC_COMM), LALT(KC_DOT), LALT(KC_SLSH), KC_RSFT, KC_TRNS, \
+ KC_LALT, KC_LGUI, LALT(KC_SPC), KC_LGUI, KC_RALT),
+
+
+ /* Layer WIN: Win layer
+ |--------+---+---+---+---+---+---+---+---+---+---+-------+----------+-------+---|
+ | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | \ | ` |
+ |--------+---+---+---+---+---+---+---+---+---+---+-------+----------+-------+---|
+ | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | Backs | |
+ |--------+---+---+---+---+---+---+---+---+---+---+-------+----------+-------+---|
+ | Contro | A | S | D | F | G | H | J | K | L | ; | ' | RCtl/Ent | | |
+ |--------+---+---+---+---+---+---+---+---+---+---+-------+----------+-------+---|
+ | Shift | Z | X | C | V | B | N | M | , | . | / | Shift | Fn0 | | |
+ |--------+---+---+---+---+---+---+---+---+---+---+-------+----------+-------+---|
+
+ |------+------+-------+------+------|
+ | LGui | LAlt | Space | RGui | Ralt |
+ |------+------+-------+------+------|
+ */
+
+ [WIN] = KEYMAP( // BASE level with swapped GUI/ALT
+
+
+ KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, \
+ KC_LCTL, LT(LGUILEV,KC_A), LT(LALTLEV,KC_S), KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, LT(RALTLEV,KC_L), LT(RGUILEV,KC_SCLN), KC_QUOT, KC_FN0, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(HHKB), \
+ KC_RGUI, KC_RALT, KC_SPC, KC_RALT, KC_RGUI)};
+
+
+const uint16_t PROGMEM fn_actions[] = {
+ [0] = ACTION_MODS_TAP_KEY(MOD_RCTL, KC_ENT) // RControl with tap Enter*
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+ // MACRODOWN only works in this function
+ switch(id) {
+ case 0:
+ if (record->event.pressed) {
+ register_code(KC_RSFT);
+ } else {
+ unregister_code(KC_RSFT);
+ }
+ break;
+ }
+ return MACRO_NONE;
+};
--- /dev/null
+/*
+Copyright 2011 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+/*
+ * scan matrix
+ */
+#include <stdint.h>
+#include <stdbool.h>
+#include <util/delay.h>
+#include "print.h"
+#include "debug.h"
+#include "util.h"
+#include "timer.h"
+#include "matrix.h"
+#include "hhkb_avr.h"
+#include <avr/wdt.h>
+#include "suspend.h"
+#include "lufa.h"
+
+
+// matrix power saving
+#define MATRIX_POWER_SAVE 10000
+static uint32_t matrix_last_modified = 0;
+
+// matrix state buffer(1:on, 0:off)
+static matrix_row_t *matrix;
+static matrix_row_t *matrix_prev;
+static matrix_row_t _matrix0[MATRIX_ROWS];
+static matrix_row_t _matrix1[MATRIX_ROWS];
+
+
+inline
+uint8_t matrix_rows(void)
+{
+ return MATRIX_ROWS;
+}
+
+inline
+uint8_t matrix_cols(void)
+{
+ return MATRIX_COLS;
+}
+
+void matrix_init(void)
+{
+#ifdef DEBUG
+ debug_enable = true;
+ debug_keyboard = true;
+#endif
+
+ KEY_INIT();
+
+ // initialize matrix state: all keys off
+ for (uint8_t i=0; i < MATRIX_ROWS; i++) _matrix0[i] = 0x00;
+ for (uint8_t i=0; i < MATRIX_ROWS; i++) _matrix1[i] = 0x00;
+ matrix = _matrix0;
+ matrix_prev = _matrix1;
+}
+
+uint8_t matrix_scan(void)
+{
+ uint8_t *tmp;
+
+ tmp = matrix_prev;
+ matrix_prev = matrix;
+ matrix = tmp;
+
+ // power on
+ if (!KEY_POWER_STATE()) KEY_POWER_ON();
+ for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+ for (uint8_t col = 0; col < MATRIX_COLS; col++) {
+ KEY_SELECT(row, col);
+ _delay_us(5);
+
+ // Not sure this is needed. This just emulates HHKB controller's behaviour.
+ if (matrix_prev[row] & (1<<col)) {
+ KEY_PREV_ON();
+ }
+ _delay_us(10);
+
+ // NOTE: KEY_STATE is valid only in 20us after KEY_ENABLE.
+ // If V-USB interrupts in this section we could lose 40us or so
+ // and would read invalid value from KEY_STATE.
+ uint8_t last = TIMER_RAW;
+
+ KEY_ENABLE();
+
+ // Wait for KEY_STATE outputs its value.
+ // 1us was ok on one HHKB, but not worked on another.
+ // no wait doesn't work on Teensy++ with pro(1us works)
+ // no wait does work on tmk PCB(8MHz) with pro2
+ // 1us wait does work on both of above
+ // 1us wait doesn't work on tmk(16MHz)
+ // 5us wait does work on tmk(16MHz)
+ // 5us wait does work on tmk(16MHz/2)
+ // 5us wait does work on tmk(8MHz)
+ // 10us wait does work on Teensy++ with pro
+ // 10us wait does work on 328p+iwrap with pro
+ // 10us wait doesn't work on tmk PCB(8MHz) with pro2(very lagged scan)
+ _delay_us(5);
+
+ if (KEY_STATE()) {
+ matrix[row] &= ~(1<<col);
+ } else {
+ matrix[row] |= (1<<col);
+ }
+
+ // Ignore if this code region execution time elapses more than 20us.
+ // MEMO: 20[us] * (TIMER_RAW_FREQ / 1000000)[count per us]
+ // MEMO: then change above using this rule: a/(b/c) = a*1/(b/c) = a*(c/b)
+ if (TIMER_DIFF_RAW(TIMER_RAW, last) > 20/(1000000/TIMER_RAW_FREQ)) {
+ matrix[row] = matrix_prev[row];
+ }
+
+ _delay_us(5);
+ KEY_PREV_OFF();
+ KEY_UNABLE();
+
+ // NOTE: KEY_STATE keep its state in 20us after KEY_ENABLE.
+ // This takes 25us or more to make sure KEY_STATE returns to idle state.
+#ifdef HHKB_JP
+ // Looks like JP needs faster scan due to its twice larger matrix
+ // or it can drop keys in fast key typing
+ _delay_us(30);
+#else
+ _delay_us(75);
+#endif
+ }
+ if (matrix[row] ^ matrix_prev[row]) matrix_last_modified = timer_read32();
+ }
+ // power off
+ if (KEY_POWER_STATE() &&
+ (USB_DeviceState == DEVICE_STATE_Suspended ||
+ USB_DeviceState == DEVICE_STATE_Unattached ) &&
+ timer_elapsed32(matrix_last_modified) > MATRIX_POWER_SAVE) {
+ KEY_POWER_OFF();
+ suspend_power_down();
+ }
+ return 1;
+}
+
+bool matrix_is_modified(void)
+{
+ for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+ if (matrix[i] != matrix_prev[i])
+ return true;
+ }
+ return false;
+}
+
+inline
+bool matrix_has_ghost(void)
+{
+ return false;
+}
+
+inline
+bool matrix_is_on(uint8_t row, uint8_t col)
+{
+ return (matrix[row] & (1<<col));
+}
+
+inline
+matrix_row_t matrix_get_row(uint8_t row)
+{
+ return matrix[row];
+}
+
+void matrix_print(void)
+{
+ print("\nr/c 01234567\n");
+ for (uint8_t row = 0; row < matrix_rows(); row++) {
+ xprintf("%02X: %08b\n", row, bitrev(matrix_get_row(row)));
+ }
+}
+
+void matrix_power_up(void) {
+ KEY_POWER_ON();
+}
+void matrix_power_down(void) {
+ KEY_POWER_OFF();
+}
projects / qmk_firmware.git / commitdiff