X-Git-Url: https://git.donarmstrong.com/?a=blobdiff_plain;f=keyboards%2Fsatan%2Fsatan.c;h=d2c5d5c2054af68b060c1d0de80a77dbe7576582;hb=79603022422cec39ea44686c84a1050acd0c145e;hp=092eb4665debb811c4e28a2e37a35f435132b2fe;hpb=649b33d7783cf3021928534b7ae127e0a89e8807;p=qmk_firmware.git

diff --git a/keyboards/satan/satan.c b/keyboards/satan/satan.c
index 092eb4665..d2c5d5c20 100644
--- a/keyboards/satan/satan.c
+++ b/keyboards/satan/satan.c
@@ -1,94 +1,30 @@
 #include "satan.h"
-
-#ifdef BACKLIGHT_ENABLE
-#include "backlight.h"
-#endif
-
-__attribute__ ((weak))
-void matrix_init_user(void) {
-	// leave these blank
-};
-
-__attribute__ ((weak))
-void matrix_scan_user(void) {
-	// leave these blank
-};
-
-
-#ifdef BACKLIGHT_ENABLE
-
-void backlight_init_ports()
-{
-
-    // Setup PB6 as output and output low.
-    DDRB |= (1<<6);
-    PORTB &= ~(1<<6);
-
-    // Use full 16-bit resolution.
-    ICR1 = 0xFFFF;
-
-    // I could write a wall of text here to explain... but TL;DW
-    // Go read the ATmega32u4 datasheet.
-    // And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on
-
-    // Pin PB6 = OCR1B (Timer 1, Channel C)
-    // Compare Output Mode = Clear on compare match, Channel C = COM1C1=1 COM1C0=0
-    // (i.e. start high, go low when counter matches.)
-    // WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0
-    // Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1
-
-    TCCR1A = _BV(COM1B1) | _BV(WGM11); // = 0b00001010;
-    TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001;
-
-    backlight_init();
-}
-
-void backlight_set(uint8_t level)
-{
-    // Prevent backlight blink on lowest level
-    PORTB &= ~(_BV(PORTB6));
-
-    if ( level == 0 )
-    {
-        // Turn off PWM control on PB6, revert to output low.
-        TCCR1A &= ~(_BV(COM1B1));
-        OCR1B = 0x0;
-    }
-    else if ( level == BACKLIGHT_LEVELS )
-    {
-        // Turn on PWM control of PB6
-        TCCR1A |= _BV(COM1B1);
-        // Set the brightness
-        OCR1B = 0xFFFF;
-    }
-    else
-    {
-        // Turn on PWM control of PB6
-        TCCR1A |= _BV(COM1B1);
-        // Set the brightness
-        OCR1B = 0xFFFF >> ((BACKLIGHT_LEVELS - level) * ((BACKLIGHT_LEVELS + 1) / 2));
-    }
-}
-
-#endif
+#include "led.h"
 
 void matrix_init_kb(void) {
 	// put your keyboard start-up code here
 	// runs once when the firmware starts up
-	if (matrix_init_user) {
-		(*matrix_init_user)();
-	}
+	matrix_init_user();
 	led_init_ports();
-
-    #ifdef BACKLIGHT_ENABLE
-        backlight_init_ports();
-    #endif
 };
 
 void matrix_scan_kb(void) {
 	// put your looping keyboard code here
 	// runs every cycle (a lot)
-	if (matrix_scan_user) {
-		(*matrix_scan_user)();
-	}
-};
\ No newline at end of file
+	matrix_scan_user();
+};
+
+void led_init_ports(void) {
+    // * Set our LED pins as output
+    DDRB |= (1<<2);
+}
+
+void led_set_kb(uint8_t usb_led) {
+    if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+        // Turn capslock on
+        PORTB &= ~(1<<2);
+    } else {
+        // Turn capslock off
+        PORTB |= (1<<2);
+    }
+}