X-Git-Url: https://git.donarmstrong.com/?a=blobdiff_plain;f=keyboards%2Fplanck%2Frules.mk;h=6097902384197bd3c9900d37926bc3e54b4b0899;hb=3cf179be61a10860b2b66aecf2ec5ca6f0e30605;hp=4423d422f6f5a6f92b531e840495ecd55672a86b;hpb=a8a1fbbac8cd941bc0b12a112fe4b06c780bc13e;p=qmk_firmware.git

diff --git a/keyboards/planck/rules.mk b/keyboards/planck/rules.mk
index 4423d422f..609790238 100644
--- a/keyboards/planck/rules.mk
+++ b/keyboards/planck/rules.mk
@@ -1,68 +1,48 @@
 # MCU name
-#MCU = at90usb1287
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded
+#     automatically (+60). See bootloader.mk for all options.
+ifeq ($(strip $(KEYBOARD)), planck/rev3)
+    BOOTLOADER = atmel-dfu
+endif
+ifeq ($(strip $(KEYBOARD)), planck/rev4)
+    BOOTLOADER = atmel-dfu
+endif
+ifeq ($(strip $(KEYBOARD)), planck/rev5)
+    BOOTLOADER = qmk-dfu
+endif
+ifeq ($(strip $(KEYBOARD)), planck/light)
+    BOOTLOADER = atmel-dfu
+endif
 
 # Interrupt driven control endpoint task(+60)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 # Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
+#   change to "no" to disable the options, or define them in the Makefile in
 #   the appropriate keymap folder that will get included automatically
 #
-BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= no         # Console for debug(+400)
-COMMAND_ENABLE ?= no        # Commands for debug and configuration
-NKRO_ENABLE ?= no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= no      # Enable keyboard backlight functionality
-MIDI_ENABLE ?= yes            # MIDI controls
-AUDIO_ENABLE ?= yes           # Audio output on port C6
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE ?= no        # Enable WS2812 RGB underlight.
-API_SYSEX_ENABLE = yes
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes         # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+NKRO_ENABLE = yes            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = yes           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
+API_SYSEX_ENABLE = no
 
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+LAYOUTS = ortho_4x12 planck_mit planck_grid
+LAYOUTS_HAS_RGB = no
+
+DEFAULT_FOLDER = planck/rev5