X-Git-Url: https://git.donarmstrong.com/?a=blobdiff_plain;f=keyboards%2Fmeira%2Frules.mk;h=6c2472f433695a5bcc51b75726865ab690d801a7;hb=6806398246c7201b84c3af508aa09b6735973d11;hp=3c69cb60a0e1a38742fea5acdf29431ffcf99c69;hpb=5fe0fe37562635caef2e6c0d9fb40832e2c332d1;p=qmk_firmware.git

diff --git a/keyboards/meira/rules.mk b/keyboards/meira/rules.mk
index 3c69cb60a..6c2472f43 100644
--- a/keyboards/meira/rules.mk
+++ b/keyboards/meira/rules.mk
@@ -4,19 +4,6 @@ SRC += matrix.c TWIlib.c issi.c lighting.c
 #MCU = at90usb1286
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
 
 #
 # LUFA specific
@@ -37,6 +24,12 @@ ARCH = AVR8
 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded 
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = caterina
+
 # Interrupt driven control endpoint task(+60)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 
@@ -53,34 +46,34 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096
 # Build Options
 #   change yes to no to disable
 #
-BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes        # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= no            # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE ?= no            # MIDI support (+2400 to 4200, depending on config)
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= no           # Audio output on port C6
-RGBLIGHT_ENABLE ?= no       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-FAUXCLICKY_ENABLE ?= no      # Use buzzer to emulate clicky switches
-
-ISSI_ENABLE ?= no			# If the I2C pullup resistors aren't install this must be disabled
-#WATCHDOG_ENABLE = yes		# Resets keyboard if matrix_scan isn't run every 250ms
+NKRO_ENABLE = no            # USB Nkey Rollover
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight. 
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+BACKLIGHT_CUSTOM_DRIVER = yes
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality, also set ISSI_ENABLE below for Miera
+ISSI_ENABLE = yes			# If the I2C pullup resistors aren't install this must be disabled
 
 CUSTOM_MATRIX = yes
 
-ifeq ($(strip $(ISSI_ENABLE)), yes)
-    TMK_COMMON_DEFS += -DISSI_ENABLE
-endif
-
-ifeq ($(strip $(WATCHDOG_ENABLE)), yes)
-    TMK_COMMON_DEFS += -DWATCHDOG_ENABLE
-endif
+#ifeq ($(strip $(ISSI_ENABLE)), yes)
+#    TMK_COMMON_DEFS += -DISSI_ENABLE
+#endif
+#
+#ifeq ($(strip $(WATCHDOG_ENABLE)), yes)
+#    TMK_COMMON_DEFS += -DWATCHDOG_ENABLE
+#endif
 
 DEFAULT_FOLDER = meira/promicro
+LAYOUTS = ortho_4x12