X-Git-Url: https://git.donarmstrong.com/?a=blobdiff_plain;f=keyboards%2Flevinson%2Frules.mk;h=8f1fa130fa62e360d447994b15fb887ff4c340cd;hb=154e1d99c398e343a6b23081e7a4ccb6e2073a8d;hp=ba0f5b91d56730800be7d16986e5cb2e1e2a7135;hpb=800ec55dfca06b4630acf62cbb5f130c4031e4f1;p=qmk_firmware.git

diff --git a/keyboards/levinson/rules.mk b/keyboards/levinson/rules.mk
index ba0f5b91d..8f1fa130f 100644
--- a/keyboards/levinson/rules.mk
+++ b/keyboards/levinson/rules.mk
@@ -1,57 +1,12 @@
-SRC += matrix.c \
-	   i2c.c \
-	   split_util.c \
-	   serial.c \
-	   ssd1306.c
-
-# MCU name
-#MCU = at90usb1287
 MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
 F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
 ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
+BOOTLOADER = caterina
 
 # Interrupt driven control endpoint task(+60)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 # Build Options
 #   change to "no" to disable the options, or define them in the Makefile in
 #   the appropriate keymap folder that will get included automatically
@@ -62,19 +17,17 @@ EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
 CONSOLE_ENABLE = no         # Console for debug(+400)
 COMMAND_ENABLE = yes        # Commands for debug and configuration
 NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
 MIDI_ENABLE = no            # MIDI controls
 AUDIO_ENABLE = no           # Audio output on port C6
 UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-SUBPROJECT_rev1 = yes
-USE_I2C = yes
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight. 
+
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
 
-CUSTOM_MATRIX = yes
+SPLIT_KEYBOARD = yes
 
 LAYOUTS = ortho_4x12
-
-DEFAULT_FOLDER = levinson/rev1
\ No newline at end of file
+DEFAULT_FOLDER = levinson/rev2