X-Git-Url: https://git.donarmstrong.com/?a=blobdiff_plain;f=keyboards%2Flets_split%2Freadme.md;h=0ef7ff59d7ede4e164dfc7d5bcecb4cd2602aa89;hb=479139f9d4ef981a2f10918f0fb5a2c148ca0c8b;hp=7e5a5460223c5108fa2cad30923445e4d3e7a9c6;hpb=bee9183e7fae7c739b9c42dd4dc759783ac80e46;p=qmk_firmware.git

diff --git a/keyboards/lets_split/readme.md b/keyboards/lets_split/readme.md
index 7e5a54602..0ef7ff59d 100644
--- a/keyboards/lets_split/readme.md
+++ b/keyboards/lets_split/readme.md
@@ -6,6 +6,7 @@ This readme and most of the code are from https://github.com/ahtn/tmk_keyboard/
 Split keyboard firmware for Arduino Pro Micro or other ATmega32u4
 based boards.
 
+**Hardware files for the Let's Split are now stored at http://qmk.fm/lets_split/**
 
 ## Build Guide
 
@@ -18,14 +19,13 @@ There is additional information there about flashing and adding RGB underglow.
 Download or clone the whole firmware and navigate to the keyboards/lets_split directory. Once your dev env is setup, you'll be able to generate the default .hex using:
 
 ```
-$ make rev2
+$ make rev2-default
 ```
 
-You will see a lot of output and if everything worked correctly you will see the built hex files:
+You will see a lot of output and if everything worked correctly you will see the built hex file:
 
 ```
-lets_split_rev2_serial.hex
-lets_split_rev2_i2c.hex
+lets_split_rev2_default.hex
 ```
 
 If you would like to use one of the alternative keymaps, or create your own, copy one of the existing [keymaps](keymaps/) and run make like so:
@@ -90,21 +90,23 @@ and modify the `matrix.c` accordingly.
 
 The wiring for serial:
 
-![serial wiring](imgs/split-keyboard-serial-schematic.png)
+![serial wiring](https://i.imgur.com/C3D1GAQ.png)
 
 The wiring for i2c:
 
-![i2c wiring](imgs/split-keyboard-i2c-schematic.png)
+![i2c wiring](https://i.imgur.com/Hbzhc6E.png)
 
 The pull-up resistors may be placed on either half. It is also possible
 to use 4 resistors and have the pull-ups in both halves, but this is
 unnecessary in simple use cases.
 
+You can change your configuration between serial and i2c by modifying your `config.h` file.
+
 Notes on Software Configuration
 -------------------------------
 
 Configuring the firmware is similar to any other QMK project. One thing
-to note is that `MATIX_ROWS` in `config.h` is the total number of rows between
+to note is that `MATRIX_ROWS` in `config.h` is the total number of rows between
 the two halves, i.e. if your split keyboard has 4 rows in each half, then
 `MATRIX_ROWS=8`.
 
@@ -113,8 +115,8 @@ not be very difficult to adapt it to support more if required.
 
 Flashing
 -------
-From the keymap directory run `make SUBPROJECT-KEYMAP-avrdude` for automatic serial port resolution and flashing.
-Example: `make rev2-serial-avrdude`
+From the `lets_split` directory run `make SUBPROJECT-KEYMAP-avrdude` for automatic serial port resolution and flashing.
+Example: `make rev2-default-avrdude`
 
 
 Choosing which board to plug the USB cable into (choosing Master)