X-Git-Url: https://git.donarmstrong.com/?a=blobdiff_plain;f=keyboards%2Fhotdox%2Frules.mk;h=be21552055ccd908a8dac57bb03c6005ef896f12;hb=b94f6cb116f1628f6d14ff3b1365bcbae6792dea;hp=f785cdd06016df209b714a9a2b935c083f25decb;hpb=188a1e66ff092a1db8adeb5410ba995715ef6594;p=qmk_firmware.git

diff --git a/keyboards/hotdox/rules.mk b/keyboards/hotdox/rules.mk
index f785cdd06..be2155205 100644
--- a/keyboards/hotdox/rules.mk
+++ b/keyboards/hotdox/rules.mk
@@ -1,63 +1,14 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make = Make software.
-#
-# make clean = Clean out built project files.
-#
-# That's pretty much all you need. To compile, always go make clean,
-# followed by make.
-#
-# For advanced users only:
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-#----------------------------------------------------------------------------
-
-# # project specific files
-SRC =  matrix.c     \
-	   i2c_master.c \
-       left.c
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Boot Section
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Build Options
@@ -79,4 +30,9 @@ SWAP_HANDS_ENABLE       = no  # Disable Onehand
 RGBLIGHT_ENABLE         = no
 MIDI_ENABLE             = no
 
+# project specific files
+SRC =  matrix.c     \
+	   i2c_master.c \
+       left.c
+
 LAYOUTS = ergodox