X-Git-Url: https://git.donarmstrong.com/?a=blobdiff_plain;f=keyboards%2Fhandwired%2Fonekey%2Frules.mk;h=245f9025d77e663aa95da2c74cbbb6e8f103858b;hb=2a56b61a28dde9e8ab0a9afcd22f913f988b2a0e;hp=c6d10856a187c74e24d0c916c83f406418128090;hpb=5cac51a773bef7fc8064390ac3ee499121a9611d;p=qmk_firmware.git

diff --git a/keyboards/handwired/onekey/rules.mk b/keyboards/handwired/onekey/rules.mk
index c6d10856a..245f9025d 100644
--- a/keyboards/handwired/onekey/rules.mk
+++ b/keyboards/handwired/onekey/rules.mk
@@ -1,65 +1,22 @@
-
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
-#   comment out to disable the options.
+#   change yes to no to disable
 #
-BOOTMAGIC_ENABLE ?= no	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes	# Console for debug(+400)
-COMMAND_ENABLE ?= yes    # Commands for debug and configuration
-#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
-
-ifndef QUANTUM_DIR
-	include ../../../Makefile
-endif
\ No newline at end of file
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = yes       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no         # Enable support for HD44780 based LCDs (+400)
+
+DEFAULT_FOLDER = handwired/onekey/promicro