X-Git-Url: https://git.donarmstrong.com/?a=blobdiff_plain;ds=sidebyside;f=keyboards%2Fergodox_ez%2Frules.mk;h=fd8f5722d39465f54b8aa6ab13ba48aafe7eeac0;hb=6a8c0a6468f4e4ce48a59152418a226d0f027497;hp=0e0b3cdefd58263bfbb250324b39a10ddbac1fb4;hpb=998ddbb122c9d3e2a77bd4e88c881b225ca0d569;p=qmk_firmware.git

diff --git a/keyboards/ergodox_ez/rules.mk b/keyboards/ergodox_ez/rules.mk
index 0e0b3cdef..fd8f5722d 100644
--- a/keyboards/ergodox_ez/rules.mk
+++ b/keyboards/ergodox_ez/rules.mk
@@ -1,68 +1,16 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make = Make software.
-#
-# make clean = Clean out built project files.
-#
-# That's pretty much all you need. To compile, always go make clean,
-# followed by make.
-#
-# For advanced users only:
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-#----------------------------------------------------------------------------
-
-# # project specific files
-SRC = matrix.c \
-  i2c_master.c
-
 # MCU name
 MCU = atmega32u4
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = halfkay
 
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # If you have Left LEDs (see
 # https://geekhack.org/index.php?topic=22780.msg873819#msg873819 for
 # details), include the following define:
@@ -82,7 +30,15 @@ UNICODE_ENABLE   = yes # Unicode
 SWAP_HANDS_ENABLE= yes # Allow swapping hands of keyboard
 SLEEP_LED_ENABLE = no
 API_SYSEX_ENABLE = no
-RGBLIGHT_ENABLE = no
-RGB_MATRIX_ENABLE = yes
+RGBLIGHT_ENABLE = yes
+RGBLIGHT_CUSTOM_DRIVER = yes
+
+RGB_MATRIX_ENABLE = no # enable later
+DEBOUNCE_TYPE = eager_pr
+
+# project specific files
+SRC += matrix.c \
+	   led_i2c.c
+QUANTUM_LIB_SRC += i2c_master.c
 
 LAYOUTS = ergodox