X-Git-Url: https://git.donarmstrong.com/?a=blobdiff_plain;ds=sidebyside;f=keyboard%2Fhhkb_rn42%2FMakefile;fp=keyboard%2Fhhkb_rn42%2FMakefile;h=3d9a602a587bf2bb3a883467e3d66747ae4c3921;hb=c5d3988e7ace6a7c940f543ab2539be8ef15bd7d;hp=0000000000000000000000000000000000000000;hpb=0c95282d3d6d1d9158a8b29b25b96609869adb0c;p=tmk_firmware.git

diff --git a/keyboard/hhkb_rn42/Makefile b/keyboard/hhkb_rn42/Makefile
new file mode 100644
index 0000000..3d9a602
--- /dev/null
+++ b/keyboard/hhkb_rn42/Makefile
@@ -0,0 +1,157 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = hhkb_lufa
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+
+# List C source files here. (C dependencies are automatically generated.)
+SRC +=	keymap_common.c \
+	matrix.c \
+	led.c
+
+CONFIG_H = config.h
+
+
+# MCU name
+# PJRC Teensy++ 2.0
+#MCU = at90usb1286
+# TMK Alt Controller or PJRC Teensy 2.0
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096	(TMK Alt Controller)
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes		# Virtual DIP switch configuration
+MOUSEKEY_ENABLE = yes		# Mouse keys
+EXTRAKEY_ENABLE = yes		# Audio control and System control
+CONSOLE_ENABLE = yes		# Console for debug
+COMMAND_ENABLE = yes    	# Commands for debug and configuration
+#NKRO_ENABLE = yes		# USB Nkey Rollover
+#KEYMAP_SECTION_ENABLE = yes	# fixed address keymap for keymap editor
+#HHKB_JP = yes			# HHKB JP support
+
+
+ifdef HHKB_JP
+    OPT_DEFS += -DHHKB_JP
+endif
+
+
+#
+# Keymap file
+#
+ifdef KEYMAP
+    SRC := keymap_$(KEYMAP).c $(SRC)
+else
+    ifdef HHKB_JP
+    	SRC := keymap_jp.c $(SRC)
+    else
+	SRC := keymap_hasu.c $(SRC)
+    endif
+endif
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include rn42.mk
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
+
+debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
+debug-on: all
+
+debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
+debug-off: all