- fi
- dst=$dst/`basename "$src"`
- fi
- fi
-
- # This sed command emulates the dirname command.
- dstdir=`echo "$dst" | sed -e 's,/*$,,;s,[^/]*$,,;s,/*$,,;s,^$,.,'`
-
- # Make sure that the destination directory exists.
-
- # Skip lots of stat calls in the usual case.
- if test ! -d "$dstdir"; then
- defaultIFS='
- '
- IFS="${IFS-$defaultIFS}"
-
- oIFS=$IFS
- # Some sh's can't handle IFS=/ for some reason.
- IFS='%'
- set x `echo "$dstdir" | sed -e 's@/@%@g' -e 's@^%@/@'`
- shift
- IFS=$oIFS
-
- pathcomp=
-
- while test $# -ne 0 ; do
- pathcomp=$pathcomp$1
- shift
- if test ! -d "$pathcomp"; then
- $mkdirprog "$pathcomp"
- # mkdir can fail with a `File exist' error in case several
- # install-sh are creating the directory concurrently. This
- # is OK.
- test -d "$pathcomp" || exit
- fi
- pathcomp=$pathcomp/
- done
- fi
-
- if test -n "$dir_arg"; then
- $doit $mkdircmd "$dst" \
- && { test -z "$chowncmd" || $doit $chowncmd "$dst"; } \
- && { test -z "$chgrpcmd" || $doit $chgrpcmd "$dst"; } \
- && { test -z "$stripcmd" || $doit $stripcmd "$dst"; } \
- && { test -z "$chmodcmd" || $doit $chmodcmd "$dst"; }
-
- else
- dstfile=`basename "$dst"`
-
- # Make a couple of temp file names in the proper directory.
- dsttmp=$dstdir/_inst.$$_
- rmtmp=$dstdir/_rm.$$_
-
- # Trap to clean up those temp files at exit.
- trap 'ret=$?; rm -f "$dsttmp" "$rmtmp" && exit $ret' 0
- trap '(exit $?); exit' 1 2 13 15
-
- # Copy the file name to the temp name.
- $doit $cpprog "$src" "$dsttmp" &&
-
- # and set any options; do chmod last to preserve setuid bits.
- #
- # If any of these fail, we abort the whole thing. If we want to
- # ignore errors from any of these, just make sure not to ignore
- # errors from the above "$doit $cpprog $src $dsttmp" command.
- #
- { test -z "$chowncmd" || $doit $chowncmd "$dsttmp"; } \
- && { test -z "$chgrpcmd" || $doit $chgrpcmd "$dsttmp"; } \
- && { test -z "$stripcmd" || $doit $stripcmd "$dsttmp"; } \
- && { test -z "$chmodcmd" || $doit $chmodcmd "$dsttmp"; } &&
-
- # Now rename the file to the real destination.
- { $doit $mvcmd -f "$dsttmp" "$dstdir/$dstfile" 2>/dev/null \
- || {
- # The rename failed, perhaps because mv can't rename something else
- # to itself, or perhaps because mv is so ancient that it does not
- # support -f.
-
- # Now remove or move aside any old file at destination location.
- # We try this two ways since rm can't unlink itself on some
- # systems and the destination file might be busy for other
- # reasons. In this case, the final cleanup might fail but the new
- # file should still install successfully.
- {
- if test -f "$dstdir/$dstfile"; then
- $doit $rmcmd -f "$dstdir/$dstfile" 2>/dev/null \
- || $doit $mvcmd -f "$dstdir/$dstfile" "$rmtmp" 2>/dev/null \
- || {
- echo "$0: cannot unlink or rename $dstdir/$dstfile" >&2
- (exit 1); exit 1
- }
- else
- :
- fi
- } &&
-
- # Now rename the file to the real destination.
- $doit $mvcmd "$dsttmp" "$dstdir/$dstfile"
- }
- }
- fi || { (exit 1); exit 1; }
+fi
+
+for srcarg in $msrc; do
+
+if [ x"$dir_arg" != x ]; then
+
+ dstarg="$srcarg"
+else
+ dstarg="$dst"
+
+# Waiting for this to be detected by the "$instcmd $srcarg $dsttmp" command
+# might cause directories to be created, which would be especially bad
+# if $src (and thus $dsttmp) contains '*'.
+
+ if [ -f "$srcarg" ]
+ then
+ doinst="$instcmd $instflags"
+ elif [ -d "$srcarg" ]
+ then
+ echo "install: $srcarg: not a regular file"
+ exit 1
+ elif [ "$srcarg" = "/dev/null" ]
+ then
+ doinst="$cpprog"
+ else
+ echo "install: $srcarg does not exist"
+ exit 1
+ fi
+
+# If destination is a directory, append the input filename; if your system
+# does not like double slashes in filenames, you may need to add some logic
+
+ if [ -d "$dstarg" ]
+ then
+ dstarg="$dstarg"/`basename "$srcarg"`
+ fi
+fi
+
+## this sed command emulates the dirname command
+dstdir=`echo "$dstarg" | sed -e 's,[^/]*$,,;s,/$,,;s,^$,.,'`
+
+# Make sure that the destination directory exists.
+# this part is taken from Noah Friedman's mkinstalldirs script
+
+# Skip lots of stat calls in the usual case.
+if [ ! -d "$dstdir" ]; then
+defaultIFS='
+'
+IFS="${IFS-${defaultIFS}}"
+
+oIFS="${IFS}"
+# Some sh's can't handle IFS=/ for some reason.
+IFS='%'
+set - `echo ${dstdir} | sed -e 's@/@%@g' -e 's@^%@/@'`
+IFS="${oIFS}"
+
+pathcomp=''
+
+while [ $# -ne 0 ] ; do
+ pathcomp="${pathcomp}${1}"
+ shift
+
+ if [ ! -d "${pathcomp}" ] ;
+ then
+ $doit $mkdirprog "${pathcomp}"
+ if [ x"$chowncmd" != x ]; then $doit $chowncmd "${pathcomp}"; else true ; fi &&
+ if [ x"$chgrpcmd" != x ]; then $doit $chgrpcmd "${pathcomp}"; else true ; fi &&
+ if [ x"$pathcompchmodcmd" != x ]; then $doit $pathcompchmodcmd "${pathcomp}"; else true ; fi
+
+ else
+ true
+ fi
+
+ pathcomp="${pathcomp}/"