SRC += matrix.c TWIlib.c issi.c lighting.c # MCU name #MCU = at90usb1286 MCU = atmega32u4 # Processor frequency. # This will define a symbol, F_CPU, in all source code files equal to the # processor frequency in Hz. You can then use this symbol in your source code to # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # # This will be an integer division of F_USB below, as it is sourced by # F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. F_CPU = 16000000 # # LUFA specific # # Target architecture (see library "Board Types" documentation). ARCH = AVR8 # Input clock frequency. # This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' # at the end, this will be done automatically to create a 32-bit value in your # source code. # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB = $(F_CPU) # Interrupt driven control endpoint task(+60) OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Boot Section Size in *bytes* # Teensy halfKay 512 # Teensy++ halfKay 1024 # Atmel DFU loader 4096 # LUFA bootloader 4096 # USBaspLoader 2048 OPT_DEFS += -DBOOTLOADER_SIZE=4096 # Build Options # change yes to no to disable # BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) CONSOLE_ENABLE ?= yes # Console for debug(+400) COMMAND_ENABLE ?= yes # Commands for debug and configuration # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work NKRO_ENABLE ?= no # USB Nkey Rollover BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default MIDI_ENABLE ?= no # MIDI support (+2400 to 4200, depending on config) UNICODE_ENABLE ?= no # Unicode BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE ?= no # Audio output on port C6 RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. FAUXCLICKY_ENABLE ?= no # Use buzzer to emulate clicky switches ISSI_ENABLE ?= no # If the I2C pullup resistors aren't install this must be disabled #WATCHDOG_ENABLE = yes # Resets keyboard if matrix_scan isn't run every 250ms CUSTOM_MATRIX = yes ifeq ($(strip $(ISSI_ENABLE)), yes) TMK_COMMON_DEFS += -DISSI_ENABLE endif ifeq ($(strip $(WATCHDOG_ENABLE)), yes) TMK_COMMON_DEFS += -DWATCHDOG_ENABLE endif DEFAULT_FOLDER = meira/promicro