1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
45 # Directory common source filess exist
47 TMK_DIR = ../../tmk_core
49 # Directory keyboard dependent files exist
52 # # project specific files
56 SRC := keymaps/$(KEYMAP).c $(SRC)
58 SRC := keymaps/default.c $(SRC)
67 # Processor frequency.
68 # This will define a symbol, F_CPU, in all source code files equal to the
69 # processor frequency in Hz. You can then use this symbol in your source code to
70 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
71 # automatically to create a 32-bit value in your source code.
73 # This will be an integer division of F_USB below, as it is sourced by
74 # F_USB after it has run through any CPU prescalers. Note that this value
75 # does not *change* the processor frequency - it should merely be updated to
76 # reflect the processor speed set externally so that the code can use accurate
84 # Target architecture (see library "Board Types" documentation).
87 # Input clock frequency.
88 # This will define a symbol, F_USB, in all source code files equal to the
89 # input clock frequency (before any prescaling is performed) in Hz. This value may
90 # differ from F_CPU if prescaling is used on the latter, and is required as the
91 # raw input clock is fed directly to the PLL sections of the AVR for high speed
92 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
93 # at the end, this will be done automatically to create a 32-bit value in your
96 # If no clock division is performed on the input clock inside the AVR (via the
97 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
100 # Interrupt driven control endpoint task(+60)
101 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
104 # Boot Section Size in *bytes*
106 # Teensy++ halfKay 1024
107 # Atmel DFU loader 4096
108 # LUFA bootloader 4096
110 OPT_DEFS += -DBOOTLOADER_SIZE=512
114 # change yes to no to disable
116 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
117 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
118 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
119 CONSOLE_ENABLE = yes # Console for debug(+400)
120 COMMAND_ENABLE = yes # Commands for debug and configuration
121 KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key
122 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
123 SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
124 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
125 NKRO_ENABLE = no # USB Nkey Rollover
126 BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
127 MIDI_ENABLE = no # MIDI controls
128 UNICODE_ENABLE = no # Unicode
129 BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
130 AUDIO_ENABLE = no # Audio output on port C6
135 ifeq ("$(wildcard keymaps/$(KEYMAP).c)","")
136 ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","")
137 include keymaps/$(KEYMAP)/makefile.mk
143 ifneq ("$(wildcard keymaps/default/makefile.mk)","")
144 include keymaps/default/makefile.mk
149 # Optimize size but this may cause error "relocation truncated to fit"
150 #EXTRALDFLAGS = -Wl,--relax
153 VPATH += $(TARGET_DIR)
157 include $(TOP_DIR)/quantum/quantum.mk