1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 SUBPROJECT_DEFAULT = rev2
46 # Processor frequency.
47 # This will define a symbol, F_CPU, in all source code files equal to the
48 # processor frequency in Hz. You can then use this symbol in your source code to
49 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
50 # automatically to create a 32-bit value in your source code.
52 # This will be an integer division of F_USB below, as it is sourced by
53 # F_USB after it has run through any CPU prescalers. Note that this value
54 # does not *change* the processor frequency - it should merely be updated to
55 # reflect the processor speed set externally so that the code can use accurate
63 # Target architecture (see library "Board Types" documentation).
66 # Input clock frequency.
67 # This will define a symbol, F_USB, in all source code files equal to the
68 # input clock frequency (before any prescaling is performed) in Hz. This value may
69 # differ from F_CPU if prescaling is used on the latter, and is required as the
70 # raw input clock is fed directly to the PLL sections of the AVR for high speed
71 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
72 # at the end, this will be done automatically to create a 32-bit value in your
75 # If no clock division is performed on the input clock inside the AVR (via the
76 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
79 # Interrupt driven control endpoint task(+60)
80 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
83 # Boot Section Size in *bytes*
85 # Teensy++ halfKay 1024
86 # Atmel DFU loader 4096
87 # LUFA bootloader 4096
89 OPT_DEFS += -DBOOTLOADER_SIZE=4096
93 # comment out to disable the options.
95 BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
96 MOUSEKEY_ENABLE ?= no # Mouse keys(+4700)
97 EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
98 CONSOLE_ENABLE ?= yes # Console for debug(+400)
99 COMMAND_ENABLE ?= yes # Commands for debug and configuration
100 NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
102 RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality
103 MIDI_ENABLE ?= no # MIDI controls
104 UNICODE_ENABLE ?= no # Unicode
105 BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
108 include ../../Makefile