1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
45 # Directory common source filess exist
47 TMK_DIR = ../../tmk_core
49 # Directory keyboard dependent files exist
52 # # project specific files
60 ifneq ("$(wildcard keymaps/$(KEYMAP).c)","")
61 KEYMAP_FILE = keymaps/$(KEYMAP).c
63 ifneq ("$(wildcard keymaps/$(KEYMAP)/keymap.c)","")
64 KEYMAP_FILE = keymaps/$(KEYMAP)/keymap.c
66 $(error Keymap file does not exist)
70 ifneq ("$(wildcard keymaps/default.c)","")
71 KEYMAP_FILE = keymaps/default.c
73 KEYMAP_FILE = keymaps/default/keymap.c
76 SRC := $(KEYMAP_FILE) $(SRC)
84 # Processor frequency.
85 # This will define a symbol, F_CPU, in all source code files equal to the
86 # processor frequency in Hz. You can then use this symbol in your source code to
87 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
88 # automatically to create a 32-bit value in your source code.
90 # This will be an integer division of F_USB below, as it is sourced by
91 # F_USB after it has run through any CPU prescalers. Note that this value
92 # does not *change* the processor frequency - it should merely be updated to
93 # reflect the processor speed set externally so that the code can use accurate
101 # Target architecture (see library "Board Types" documentation).
104 # Input clock frequency.
105 # This will define a symbol, F_USB, in all source code files equal to the
106 # input clock frequency (before any prescaling is performed) in Hz. This value may
107 # differ from F_CPU if prescaling is used on the latter, and is required as the
108 # raw input clock is fed directly to the PLL sections of the AVR for high speed
109 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
110 # at the end, this will be done automatically to create a 32-bit value in your
113 # If no clock division is performed on the input clock inside the AVR (via the
114 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
117 # Interrupt driven control endpoint task(+60)
118 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
121 # Boot Section Size in *bytes*
123 # Teensy++ halfKay 1024
124 # Atmel DFU loader 4096
125 # LUFA bootloader 4096
127 OPT_DEFS += -DBOOTLOADER_SIZE=4096
131 # comment out to disable the options.
133 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
134 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
135 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
136 CONSOLE_ENABLE = yes # Console for debug(+400)
137 COMMAND_ENABLE = yes # Commands for debug and configuration
138 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
139 # SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
140 # NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
141 BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
142 MIDI_ENABLE = YES # MIDI controls
143 AUDIO_ENABLE = YES # Audio output on port C6
144 # UNICODE_ENABLE = YES # Unicode
145 # BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
146 # RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. Do not enable this with MIDI at the same time.
148 ifdef BACKLIGHT_ENABLE
153 # Optimize size but this may cause error "relocation truncated to fit"
154 #EXTRALDFLAGS = -Wl,--relax
157 VPATH += $(TARGET_DIR)
161 include $(TOP_DIR)/quantum/quantum.mk