// - unused : input : 1
// - input : input : 1
// - driving : output : 0
- mcp23018_status = i2c_start(I2C_ADDR_WRITE, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_write(IODIRA, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_write(0b10000000, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_write(0b11111111, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_start(I2C_ADDR_WRITE, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_write(IODIRA, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_write(0b10000000, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_write(0b11111111, I2C_TIMEOUT); if (mcp23018_status) goto out;
i2c_stop();
// set pull-up
// - unused : on : 1
// - input : on : 1
// - driving : off : 0
- mcp23018_status = i2c_start(I2C_ADDR_WRITE, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_write(GPPUA, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_write(0b10000000, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_write(0b11111111, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_start(I2C_ADDR_WRITE, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_write(GPPUA, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_write(0b10000000, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_write(0b11111111, I2C_TIMEOUT); if (mcp23018_status) goto out;
out:
i2c_stop();
#pragma once
-#include <util/delay.h>
+
+#include "quantum.h"
#include <stdint.h>
#include <stdbool.h>
-#include "quantum.h"
#include "i2c_master.h"
-#include "matrix.h"
+#include <util/delay.h>
extern i2c_status_t mcp23018_status;
-#define ERGODOX_EZ_I2C_TIMEOUT 1000
+#define I2C_TIMEOUT 1000
#define CPU_PRESCALE(n) (CLKPR = 0x80, CLKPR = (n))
#define CPU_16MHz 0x00
#define OLATA 0x14 // output latch register
#define OLATB 0x15
-void init_ergodox(void);
uint8_t init_mcp23018(void);
/* ---------- LEFT HAND ----------- ---------- RIGHT HAND ---------- */
-#define LAYOUT_GERGO( \
+#define LAYOUT_gergo( \
L00,L01,L02,L03,L04,L05, R00,R01,R02,R03,R04,R05, \
L10,L11,L12,L13,L14,L15,L16, R10,R11,R12,R13,R14,R15,R16, \
- L20,L21,L22,L23,L24,L25,L26, R20,R21,R22,R23,R24,R25,R26, \
- L31,L32, R33,R34, \
- L30, R30, \
- L33,L34, R31,R32) \
- \
+ L20,L21,L22,L23,L24,L25,L26,L30, R30,R20,R21,R22,R23,R24,R25,R26, \
+ L31,L32,L33,L34, R31,R32,R33,R34) \
/* matrix positions */ \
{ \
{ KC_NO, L16, L26, L30}, \
+++ /dev/null
-#ifndef _I2CMASTER_H
-#define _I2CMASTER_H 1
-/*************************************************************************
-* Title: C include file for the I2C master interface
-* (i2cmaster.S or twimaster.c)
-* Author: Peter Fleury <pfleury@gmx.ch> http://jump.to/fleury
-* File: $Id: i2cmaster.h,v 1.10 2005/03/06 22:39:57 Peter Exp $
-* Software: AVR-GCC 3.4.3 / avr-libc 1.2.3
-* Target: any AVR device
-* Usage: see Doxygen manual
-**************************************************************************/
-
-#ifdef DOXYGEN
-/**
- @defgroup pfleury_ic2master I2C Master library
- @code #include <i2cmaster.h> @endcode
-
- @brief I2C (TWI) Master Software Library
-
- Basic routines for communicating with I2C slave devices. This single master
- implementation is limited to one bus master on the I2C bus.
-
- This I2c library is implemented as a compact assembler software implementation of the I2C protocol
- which runs on any AVR (i2cmaster.S) and as a TWI hardware interface for all AVR with built-in TWI hardware (twimaster.c).
- Since the API for these two implementations is exactly the same, an application can be linked either against the
- software I2C implementation or the hardware I2C implementation.
-
- Use 4.7k pull-up resistor on the SDA and SCL pin.
-
- Adapt the SCL and SDA port and pin definitions and eventually the delay routine in the module
- i2cmaster.S to your target when using the software I2C implementation !
-
- Adjust the CPU clock frequence F_CPU in twimaster.c or in the Makfile when using the TWI hardware implementaion.
-
- @note
- The module i2cmaster.S is based on the Atmel Application Note AVR300, corrected and adapted
- to GNU assembler and AVR-GCC C call interface.
- Replaced the incorrect quarter period delays found in AVR300 with
- half period delays.
-
- @author Peter Fleury pfleury@gmx.ch http://jump.to/fleury
-
- @par API Usage Example
- The following code shows typical usage of this library, see example test_i2cmaster.c
-
- @code
-
- #include <i2cmaster.h>
-
-
- #define Dev24C02 0xA2 // device address of EEPROM 24C02, see datasheet
-
- int main(void)
- {
- unsigned char ret;
-
- i2c_init(); // initialize I2C library
-
- // write 0x75 to EEPROM address 5 (Byte Write)
- i2c_start_wait(Dev24C02+I2C_WRITE); // set device address and write mode
- i2c_write(0x05); // write address = 5
- i2c_write(0x75); // write value 0x75 to EEPROM
- i2c_stop(); // set stop conditon = release bus
-
-
- // read previously written value back from EEPROM address 5
- i2c_start_wait(Dev24C02+I2C_WRITE); // set device address and write mode
-
- i2c_write(0x05); // write address = 5
- i2c_rep_start(Dev24C02+I2C_READ); // set device address and read mode
-
- ret = i2c_readNak(); // read one byte from EEPROM
- i2c_stop();
-
- for(;;);
- }
- @endcode
-
-*/
-#endif /* DOXYGEN */
-
-/**@{*/
-
-#if (__GNUC__ * 100 + __GNUC_MINOR__) < 304
-#error "This library requires AVR-GCC 3.4 or later, update to newer AVR-GCC compiler !"
-#endif
-
-#include <avr/io.h>
-
-/** defines the data direction (reading from I2C device) in i2c_start(),i2c_rep_start() */
-#define I2C_READ 1
-
-/** defines the data direction (writing to I2C device) in i2c_start(),i2c_rep_start() */
-#define I2C_WRITE 0
-
-
-/**
- @brief initialize the I2C master interace. Need to be called only once
- @param void
- @return none
- */
-void i2c_init(void);
-
-
-/**
- @brief Terminates the data transfer and releases the I2C bus
- @param void
- @return none
- */
-void i2c_stop(void);
-
-
-/**
- @brief Issues a start condition and sends address and transfer direction
-
- @param addr address and transfer direction of I2C device
- @retval 0 device accessible
- @retval 1 failed to access device
- */
-unsigned char i2c_start(unsigned char addr);
-
-
-/**
- @brief Issues a repeated start condition and sends address and transfer direction
-
- @param addr address and transfer direction of I2C device
- @retval 0 device accessible
- @retval 1 failed to access device
- */
-unsigned char i2c_rep_start(unsigned char addr);
-
-
-/**
- @brief Issues a start condition and sends address and transfer direction
-
- If device is busy, use ack polling to wait until device ready
- @param addr address and transfer direction of I2C device
- @return none
- */
-void i2c_start_wait(unsigned char addr);
-
-
-/**
- @brief Send one byte to I2C device
- @param data byte to be transfered
- @retval 0 write successful
- @retval 1 write failed
- */
-unsigned char i2c_write(unsigned char data);
-
-
-/**
- @brief read one byte from the I2C device, request more data from device
- @return byte read from I2C device
- */
-unsigned char i2c_readAck(void);
-
-/**
- @brief read one byte from the I2C device, read is followed by a stop condition
- @return byte read from I2C device
- */
-unsigned char i2c_readNak(void);
-
-/**
- @brief read one byte from the I2C device
-
- Implemented as a macro, which calls either i2c_readAck or i2c_readNak
-
- @param ack 1 send ack, request more data from device<br>
- 0 send nak, read is followed by a stop condition
- @return byte read from I2C device
- */
-unsigned char i2c_read(unsigned char ack);
-#define i2c_read(ack) (ack) ? i2c_readAck() : i2c_readNak();
-
-
-/**@}*/
-#endif
"keyboard_name": "Gergo",
"url": "http://gboards.ca",
"layouts": {
- "LAYOUT_GERGO": {
+ "LAYOUT_gergo": {
"layout": [
{
"label": "L00",
"x": 6.5,
"y": 1.75
},
+ {
+ "label": "L30",
+ "x": 8.25,
+ "y": 2.75
+ },
+ {
+ "label": "R30",
+ "x": 10.25,
+ "y": 2.75
+ },
{
"h": 1.5,
"label": "R20",
"x": 6,
"y": 3.63
},
- {
- "label": "R33",
- "x": 12.5,
- "y": 3.63
- },
- {
- "label": "R34",
- "x": 13.75,
- "y": 3.25
- },
- {
- "label": "L30",
- "x": 8.25,
- "y": 2.75
- },
- {
- "label": "R30",
- "x": 10.25,
- "y": 2.75
- },
{
"h": 2,
"label": "L33",
"label": "R32",
"x": 11.25,
"y": 3.75
+ },
+ {
+ "label": "R33",
+ "x": 12.5,
+ "y": 3.63
+ },
+ {
+ "label": "R34",
+ "x": 13.75,
+ "y": 3.25
}
]
}
--- /dev/null
+#pragma once
+
+#define IGNORE_MOD_TAP_INTERRUPT
-/* Good on you for modifying your layout! if you don't have
+/* Good on you for modifying your layout! if you don't have
* time to read the QMK docs, a list of keycodes can be found at
*
* https://github.com/qmk/qmk_firmware/blob/master/docs/keycodes.md
#include QMK_KEYBOARD_H
-#define IGNORE_MOD_TAP_INTERRUPT
#define BASE 0 // default layer
#define SYMB 1 // symbols
#define NUMB 2 // numbers/motion
* | | | | | |
* `--------------' `--------------'
*/
-[BASE] = LAYOUT_GERGO(
-LT(NUMB, KC_ESC), KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_PIPE,
-MT(MOD_LCTL, KC_BSPC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_BTN2, KC_TRNS, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT,
-KC_RSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_BTN1, KC_BSPC, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_MINS,
-
- MT(MOD_LGUI, KC_DEL), MT(MOD_LALT, KC_ENT), KC_TAB, KC_BSPC,
-
- KC_BTN3, KC_PGDN,
- LT(SYMB, KC_SPC), LT(NUMB, KC_ESC), LT(SYMB, KC_ENT), LT(NUMB, KC_SPC)),
+[BASE] = LAYOUT_gergo(
+ LT(NUMB, KC_ESC), KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_PIPE,
+ MT(MOD_LCTL, KC_BSPC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_BTN2, KC_TRNS, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT,
+ KC_RSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_BTN1, KC_BTN3, KC_PGDN, KC_BSPC, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_MINS,
+ MT(MOD_LGUI, KC_DEL), MT(MOD_LALT, KC_ENT), LT(SYMB, KC_SPC), LT(NUMB, KC_ESC), LT(SYMB, KC_ENT), LT(NUMB, KC_SPC), KC_TAB, KC_BSPC
+ ),
/* Keymap 1: Symbols layer
*
* ,-------------------------------------------. ,-------------------------------------------.
* | | | | | |
* `--------------' `--------------'
*/
-[SYMB] = LAYOUT_GERGO(
-KC_TRNS, KC_EXLM, KC_AT, KC_LCBR,KC_RCBR, KC_PIPE, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_BSLS,
-KC_TRNS, KC_HASH, KC_DLR, KC_LPRN,KC_RPRN, KC_GRV, KC_TRNS, KC_TRNS, KC_PLUS, KC_MINS, KC_SLSH, KC_ASTR, KC_PERC, KC_QUOT,
-KC_TRNS, KC_PERC, KC_CIRC,KC_LBRC,KC_RBRC, KC_TILD, KC_TRNS, KC_TRNS, KC_AMPR, KC_EQL, KC_COMM, KC_DOT, KC_SLSH, KC_MINS,
-
- KC_TRNS, KC_TRNS, KC_PGUP, KC_DEL,
- KC_TRNS, KC_TRNS,
- KC_SCLN, KC_EQL, KC_EQL, KC_SCLN),
+[SYMB] = LAYOUT_gergo(
+ KC_TRNS, KC_EXLM, KC_AT, KC_LCBR, KC_RCBR, KC_PIPE, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_BSLS,
+ KC_TRNS, KC_HASH, KC_DLR, KC_LPRN, KC_RPRN, KC_GRV, KC_TRNS, KC_TRNS, KC_PLUS, KC_MINS, KC_SLSH, KC_ASTR, KC_PERC, KC_QUOT,
+ KC_TRNS, KC_PERC, KC_CIRC, KC_LBRC, KC_RBRC, KC_TILD, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_AMPR, KC_EQL, KC_COMM, KC_DOT, KC_SLSH, KC_MINS,
+ KC_TRNS, KC_TRNS, KC_SCLN, KC_EQL, KC_EQL, KC_SCLN, KC_PGUP, KC_DEL
+ ),
/* Keymap 2: Pad/Function layer
*
* ,-------------------------------------------. ,-------------------------------------------.
* | | | | | |
* `--------------' `--------------'
*/
-[NUMB] = LAYOUT_GERGO(
-KC_TRNS, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_TRNS,
-KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_TRNS, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, KC_VOLD, KC_VOLU,
-KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_MS_L, KC_MS_D, KC_MS_U, KC_MS_R, KC_MPLY, KC_MNXT,
-
- KC_TRNS, KC_TRNS, KC_PGUP, KC_TRNS,
- KC_TRNS, KC_TRNS,
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS)
+[NUMB] = LAYOUT_gergo(
+ KC_TRNS, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_TRNS,
+ KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_TRNS, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, KC_VOLD, KC_VOLU,
+ KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, KC_TRNS, KC_MS_L, KC_MS_D, KC_MS_U, KC_MS_R, KC_MPLY, KC_MNXT,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS
+ ),
};
-/* Keymap template
+/* Keymap template
*
* ,-------------------------------------------. ,-------------------------------------------.
* | | | | | | | | | | | | | |
* | | | | | |
* | | | | | |
* `--------------' `--------------'
-[SYMB] = LAYOUT_GERGO(
-KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
-KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
-KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
-
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- KC_TRNS, KC_TRNS,
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+[SYMB] = LAYOUT_gergo(
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS
+ )
*/
-
-// Runs just one time when the keyboard initializes.
-void matrix_init_user(void) {
-
-};
-
-// Runs constantly in the background, in a loop.
-void matrix_scan_user(void) {
- //uint8_t layer = biton32(layer_state);
- biton32(layer_state);
-};
-
-
--- /dev/null
+/* Good on you for modifying your layout! if you don't have
+ * time to read the QMK docs, a list of keycodes can be found at
+ *
+ * https://github.com/qmk/qmk_firmware/blob/master/docs/keycodes.md
+ *
+ * There's also a template for adding new layers at the bottom of this file!
+ */
+
+#include QMK_KEYBOARD_H
+#include "drashna.h"
+
+// Blank template at the bottom
+
+enum customKeycodes {
+ URL = 1
+};
+
+#define LAYOUT_gergo_wrapper(...) LAYOUT_gergo(__VA_ARGS__)
+#define LAYOUT_gergo_base( \
+ K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, \
+ K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, \
+ K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A \
+ ) \
+ LAYOUT_gergo_wrapper( \
+ KC_ESC, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, KC_PIPE, \
+ KC_TAB, ALT_T(K11), K12, K13, K14, K15, _______, _______, K16, K17, K18, K19, K1A, RGUI_T(KC_QUOT), \
+ OS_LSFT, CTL_T(K21), K22, K23, K24, K25, _______, _______, _______, _______, K26, K27, K28, K29, CTL_T(K2A), OS_RSFT, \
+ _______, _______, KC_SPC, LT(_LOWER, KC_BSPC), LT(_RAISE, KC_DEL), KC_ENT, _______, _______ \
+ )
+
+#define LAYOUT_gergo_base_wrapper(...) LAYOUT_gergo_base(__VA_ARGS__)
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ [_QWERTY] = LAYOUT_gergo_base_wrapper(
+ _________________QWERTY_L1_________________, _________________QWERTY_R1_________________,
+ _________________QWERTY_L2_________________, _________________QWERTY_R2_________________,
+ _________________QWERTY_L3_________________, _________________QWERTY_R3_________________
+ ),
+ [_COLEMAK] = LAYOUT_gergo_base_wrapper(
+ _________________COLEMAK_L1________________, _________________COLEMAK_R1________________,
+ _________________COLEMAK_L2________________, _________________COLEMAK_R2________________,
+ _________________COLEMAK_L3________________, _________________COLEMAK_R3________________
+ ),
+
+ [_DVORAK] = LAYOUT_gergo_base_wrapper(
+ _________________DVORAK_L1_________________, _________________DVORAK_R1_________________,
+ _________________DVORAK_L2_________________, _________________DVORAK_R2_________________,
+ _________________DVORAK_L3_________________, _________________DVORAK_R3_________________
+ ),
+
+ [_WORKMAN] = LAYOUT_gergo_base_wrapper(
+ _________________WORKMAN_L1________________, _________________WORKMAN_R1________________,
+ _________________WORKMAN_L2________________, _________________WORKMAN_R2________________,
+ _________________WORKMAN_L3________________, _________________WORKMAN_R3________________
+ ),
+
+ [_NORMAN] = LAYOUT_gergo_base_wrapper(
+ _________________NORMAN_L1_________________, _________________NORMAN_L1_________________,
+ _________________NORMAN_L2_________________, _________________NORMAN_R2_________________,
+ _________________NORMAN_L3_________________, _________________NORMAN_R3_________________
+ ),
+
+ [_MALTRON] = LAYOUT_gergo_base_wrapper(
+ _________________MALTRON_L1________________, _________________MALTRON_R1________________,
+ _________________MALTRON_L2________________, _________________MALTRON_R2________________,
+ _________________MALTRON_L3________________, _________________MALTRON_R3________________
+ ),
+
+ [_EUCALYN] = LAYOUT_gergo_base_wrapper(
+ _________________EUCALYN_L1________________, _________________EUCALYN_R1________________,
+ _________________EUCALYN_L2________________, _________________EUCALYN_R2________________,
+ _________________EUCALYN_L3________________, _________________EUCALYN_R3________________
+ ),
+
+ [_CARPLAX] = LAYOUT_gergo_base_wrapper(
+ _____________CARPLAX_QFMLWY_L1_____________, _____________CARPLAX_QFMLWY_R1_____________,
+ _____________CARPLAX_QFMLWY_L2_____________, _____________CARPLAX_QFMLWY_R2_____________,
+ _____________CARPLAX_QFMLWY_L3_____________, _____________CARPLAX_QFMLWY_R3_____________
+ ),
+
+ [_MODS] = LAYOUT_gergo_wrapper(
+ _______, ___________________BLANK___________________, ___________________BLANK___________________, _______,
+ _______, ___________________BLANK___________________, _______, _______, ___________________BLANK___________________, _______,
+ KC_LSFT, ___________________BLANK___________________, _______, _______, _______, _______, ___________________BLANK___________________, KC_RSFT,
+ _______, _______, _______, _______, _______, _______, _______, _______
+ ),
+ [_LOWER] = LAYOUT_gergo_wrapper(
+ KC_F12, _________________LOWER_L1__________________, _________________LOWER_R1__________________, KC_F11,
+ _______, _________________LOWER_L2__________________, _______, _______, _________________LOWER_R2__________________, KC_PIPE,
+ _______, _________________LOWER_L3__________________, _______, _______, _______, _______, _________________LOWER_R3__________________, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______
+ ),
+
+ [_RAISE] = LAYOUT_gergo_wrapper(
+ _______, _________________RAISE_L1__________________, _________________RAISE_R1__________________, _______,
+ _______, _________________RAISE_L2__________________, _______, _______, _________________RAISE_R2__________________, KC_BSLS,
+ _______, _________________RAISE_L3__________________, _______, _______, _______, _______, _________________RAISE_R3__________________, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______
+ ),
+
+ [_ADJUST] = LAYOUT_gergo_wrapper(
+ KC_MAKE, _________________ADJUST_L1_________________, _________________ADJUST_R1_________________, KC_RESET,
+ VRSN, _________________ADJUST_L2_________________, _______, KC_NUKE, _________________ADJUST_R2_________________, EEP_RST,
+ _______, _________________ADJUST_L3_________________, _______, _______, _______, _______, _________________ADJUST_R3_________________, TG_MODS,
+ _______, _______, _______, _______, _______, _______, _______, _______
+ ),
+
+};
+
+/* Keymap template
+
+ [SYMB] = LAYOUT_gergo_wrapper(
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
+ _______, _______, _______, _______, _______, _______, _______, _______
+ ),
+
+ */
--- /dev/null
+#pragma once
+
+#define IGNORE_MOD_TAP_INTERRUPT
-/* Good on you for modifying your layout! if you don't have
+/* Good on you for modifying your layout! if you don't have
* time to read the QMK docs, a list of keycodes can be found at
*
* https://github.com/qmk/qmk_firmware/blob/master/docs/keycodes.md
#include QMK_KEYBOARD_H
-#define IGNORE_MOD_TAP_INTERRUPT
#define BASE 0 // default layer
#define SYMB 1 // symbols
#define NUMB 2 // numbers/motion
* | | | | | |
* `--------------' `--------------'
*/
-[BASE] = LAYOUT_GERGO(
-LT(NUMB, KC_ESC), KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_PIPE,
-MT(MOD_LCTL, KC_BSPC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_BTN2, KC_TRNS, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT,
-KC_RSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_BTN1, KC_BSPC, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_MINS,
-
- MT(MOD_LGUI, KC_DEL), MT(MOD_LALT, KC_ENT), KC_TAB, KC_BSPC,
-
- KC_BTN3, KC_PGDN,
- LT(SYMB, KC_SPC), LT(NUMB, KC_ESC), LT(SYMB, KC_ENT), LT(NUMB, KC_SPC)),
+[BASE] = LAYOUT_gergo(
+ LT(NUMB, KC_ESC), KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_PIPE,
+ MT(MOD_LCTL, KC_BSPC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_BTN2, KC_TRNS, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT,
+ KC_RSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_BTN1, KC_BTN3, KC_PGDN, KC_BSPC, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_MINS,
+ MT(MOD_LGUI, KC_DEL), MT(MOD_LALT, KC_ENT), LT(SYMB, KC_SPC), LT(NUMB, KC_ESC), LT(SYMB, KC_ENT), LT(NUMB, KC_SPC), KC_TAB, KC_BSPC
+ ),
/* Keymap 1: Symbols layer
*
* ,-------------------------------------------. ,-------------------------------------------.
* | | | | | |
* `--------------' `--------------'
*/
-[SYMB] = LAYOUT_GERGO(
-KC_TRNS, KC_EXLM, KC_AT, KC_LCBR,KC_RCBR, KC_PIPE, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_BSLS,
-KC_TRNS, KC_HASH, KC_DLR, KC_LPRN,KC_RPRN, KC_GRV, KC_TRNS, KC_TRNS, KC_PLUS, KC_MINS, KC_SLSH, KC_ASTR, KC_PERC, KC_QUOT,
-KC_TRNS, KC_PERC, KC_CIRC,KC_LBRC,KC_RBRC, KC_TILD, KC_TRNS, KC_TRNS, KC_AMPR, KC_EQL, KC_COMM, KC_DOT, KC_SLSH, KC_MINS,
-
- KC_TRNS, KC_TRNS, KC_PGUP, KC_DEL,
- KC_TRNS, KC_TRNS,
- KC_SCLN, KC_EQL, KC_EQL, KC_SCLN),
+[SYMB] = LAYOUT_gergo(
+ KC_TRNS, KC_EXLM, KC_AT, KC_LCBR, KC_RCBR, KC_PIPE, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_BSLS,
+ KC_TRNS, KC_HASH, KC_DLR, KC_LPRN, KC_RPRN, KC_GRV, KC_TRNS, KC_TRNS, KC_PLUS, KC_MINS, KC_SLSH, KC_ASTR, KC_PERC, KC_QUOT,
+ KC_TRNS, KC_PERC, KC_CIRC, KC_LBRC, KC_RBRC, KC_TILD, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_AMPR, KC_EQL, KC_COMM, KC_DOT, KC_SLSH, KC_MINS,
+ KC_TRNS, KC_TRNS, KC_SCLN, KC_EQL, KC_EQL, KC_SCLN, KC_PGUP, KC_DEL
+ ),
/* Keymap 2: Pad/Function layer
*
* ,-------------------------------------------. ,-------------------------------------------.
* | | | | | |
* `--------------' `--------------'
*/
-[NUMB] = LAYOUT_GERGO(
-KC_TRNS, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_TRNS,
-KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_TRNS, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, KC_VOLD, KC_VOLU,
-KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_MS_L, KC_MS_D, KC_MS_U, KC_MS_R, KC_MPLY, KC_MNXT,
-
- KC_TRNS, KC_TRNS, KC_PGUP, KC_TRNS,
- KC_TRNS, KC_TRNS,
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS)
+[NUMB] = LAYOUT_gergo(
+ KC_TRNS, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_TRNS,
+ KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_TRNS, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, KC_VOLD, KC_VOLU,
+ KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, KC_TRNS, KC_MS_L, KC_MS_D, KC_MS_U, KC_MS_R, KC_MPLY, KC_MNXT,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS
+ ),
};
-/* Keymap template
+/* Keymap template
*
* ,-------------------------------------------. ,-------------------------------------------.
* | | | | | | | | | | | | | |
* | | | | | |
* | | | | | |
* `--------------' `--------------'
-[SYMB] = LAYOUT_GERGO(
-KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
-KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
-KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
-
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
- KC_TRNS, KC_TRNS,
- KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+[SYMB] = LAYOUT_gergo(
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS
+ )
*/
-
-// Runs just one time when the keyboard initializes.
-void matrix_init_user(void) {
-
-};
-
-// Runs constantly in the background, in a loop.
-void matrix_scan_user(void) {
- //uint8_t layer = biton32(layer_state);
- biton32(layer_state);
-};
-
-
#include "print.h"
#include "debug.h"
#include "util.h"
+#include "debounce.h"
#include "pointing_device.h"
#include QMK_KEYBOARD_H
#ifdef DEBUG_MATRIX_SCAN_RATE
-#include "timer.h"
+# include "timer.h"
#endif
#ifdef BALLER
// Debouncing: store for each key the number of scans until it's eligible to
// change. When scanning the matrix, ignore any changes in keys that have
// already changed in the last DEBOUNCE scans.
-static uint8_t debounce_matrix[MATRIX_ROWS * MATRIX_COLS];
static matrix_row_t read_cols(uint8_t row);
-static void init_cols(void);
-static void unselect_rows(void);
-static void select_row(uint8_t row);
+static void init_cols(void);
+static void unselect_rows(void);
+static void select_row(uint8_t row);
static void enableInterrupts(void);
static uint8_t mcp23018_reset_loop;
#endif
-__attribute__ ((weak))
-void matrix_init_user(void) {}
+__attribute__ ((weak)) void matrix_init_user(void) {}
-__attribute__ ((weak))
-void matrix_scan_user(void) {}
+__attribute__ ((weak)) void matrix_scan_user(void) {}
__attribute__ ((weak))
void matrix_init_kb(void) {
matrix_scan_user();
}
-inline
-uint8_t matrix_rows(void)
-{
- return MATRIX_ROWS;
-}
+inline uint8_t matrix_rows(void) { return MATRIX_ROWS; }
-inline
-uint8_t matrix_cols(void)
-{
- return MATRIX_COLS;
-}
+inline uint8_t matrix_cols(void) { return MATRIX_COLS; }
-void matrix_init(void)
-{
+void matrix_init(void) {
// initialize row and col
mcp23018_status = init_mcp23018();
unselect_rows();
init_cols();
- // initialize matrix state: all keys off
- for (uint8_t i=0; i < MATRIX_ROWS; i++) {
- matrix[i] = 0;
- raw_matrix[i] = 0;
- for (uint8_t j=0; j < MATRIX_COLS; ++j) {
- debounce_matrix[i * MATRIX_COLS + j] = 0;
- }
- }
+ // initialize matrix state: all keys off
+ for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+ matrix[i] = 0;
+ raw_matrix[i] = 0;
+ }
#ifdef DEBUG_MATRIX_SCAN_RATE
- matrix_timer = timer_read32();
+ matrix_timer = timer_read32();
matrix_scan_count = 0;
#endif
+ debounce_init(MATRIX_ROWS);
matrix_init_quantum();
}
}
#ifdef DEBUG_MATRIX_SCAN_RATE
- matrix_timer = timer_read32();
+ matrix_timer = timer_read32();
matrix_scan_count = 0;
#endif
}
-// Returns a matrix_row_t whose bits are set if the corresponding key should be
-// eligible to change in this scan.
-matrix_row_t debounce_mask(matrix_row_t rawcols, uint8_t row) {
- matrix_row_t result = 0;
- matrix_row_t change = rawcols ^ raw_matrix[row];
- raw_matrix[row] = rawcols;
- for (uint8_t i = 0; i < MATRIX_COLS; ++i) {
- if (debounce_matrix[row * MATRIX_COLS + i]) {
- --debounce_matrix[row * MATRIX_COLS + i];
- } else {
- result |= (1 << i);
- }
- if (change & (1 << i)) {
- debounce_matrix[row * MATRIX_COLS + i] = DEBOUNCE;
- }
+// Reads and stores a row, returning
+// whether a change occurred.
+static inline bool store_raw_matrix_row(uint8_t index) {
+ matrix_row_t temp = read_cols(index);
+ if (raw_matrix[index] != temp) {
+ raw_matrix[index] = temp;
+ return true;
}
- return result;
+ return false;
}
-matrix_row_t debounce_read_cols(uint8_t row) {
- // Read the row without debouncing filtering and store it for later usage.
- matrix_row_t cols = read_cols(row);
- // Get the Debounce mask.
- matrix_row_t mask = debounce_mask(cols, row);
- // debounce the row and return the result.
- return (cols & mask) | (matrix[row] & ~mask);;
-}
-uint8_t matrix_scan(void)
-{
- // TODO: Find what is trashing interrupts
- enableInterrupts();
- // First we handle the mouse inputs
- #ifdef BALLER
- uint8_t pBtn = PINE & TRKBTN;
+uint8_t matrix_scan(void) {
+ // TODO: Find what is trashing interrupts
+ enableInterrupts();
+
+ // First we handle the mouse inputs
+#ifdef BALLER
+ uint8_t pBtn = PINE & TRKBTN;
- #ifdef DEBUG_BALLER
- // Compare to previous, mod report
- if (tbUpCnt + tbDnCnt + tbLtCnt + tbRtCnt != 0)
- xprintf("U: %d D: %d L: %d R: %d B: %d\n", tbUpCnt, tbDnCnt, tbLtCnt, tbRtCnt, (trkBtnState >> 6));
- #endif
+ #ifdef DEBUG_BALLER
+ // Compare to previous, mod report
+ if (tbUpCnt + tbDnCnt + tbLtCnt + tbRtCnt != 0)
+ xprintf("U: %d D: %d L: %d R: %d B: %d\n", tbUpCnt, tbDnCnt, tbLtCnt, tbRtCnt, (trkBtnState >> 6));
+ #endif
- // Modify the report
- report_mouse_t pRprt = pointing_device_get_report();
+ // Modify the report
+ report_mouse_t pRprt = pointing_device_get_report();
- // Scroll by default, move on layer
- if (layer_state == 0) {
+ // Scroll by default, move on layer
+ if (layer_state == 0) {
pRprt.h += tbLtCnt * SCROLLSTEP; tbLtCnt = 0;
pRprt.h -= tbRtCnt * SCROLLSTEP; tbRtCnt = 0;
pRprt.v -= tbUpCnt * SCROLLSTEP; tbUpCnt = 0;
pRprt.v += tbDnCnt * SCROLLSTEP; tbDnCnt = 0;
- } else {
+ } else {
pRprt.x -= tbLtCnt * TRKSTEP * (layer_state - 1); tbLtCnt = 0;
pRprt.x += tbRtCnt * TRKSTEP * (layer_state - 1); tbRtCnt = 0;
pRprt.y -= tbUpCnt * TRKSTEP * (layer_state - 1); tbUpCnt = 0;
pRprt.y += tbDnCnt * TRKSTEP * (layer_state - 1); tbDnCnt = 0;
- }
+ }
- #ifdef DEBUG_BALLER
- if (pRprt.x != 0 || pRprt.y != 0)
- xprintf("X: %d Y: %d\n", pRprt.x, pRprt.y);
- #endif
-
- if ((pBtn != trkBtnState) && ((pBtn >> 6) == 0)) pRprt.buttons |= MOUSE_BTN1;
- if ((pBtn != trkBtnState) && ((pBtn >> 6) == 1)) pRprt.buttons &= ~MOUSE_BTN1;
-
- // Save state, push update
- if (pRprt.x != 0 || pRprt.y != 0 || pRprt.h != 0 || pRprt.v != 0 || (trkBtnState != pBtn))
- pointing_device_set_report(pRprt);
-
- trkBtnState = pBtn;
- #endif
-
- // Then the keyboard
- if (mcp23018_status) { // if there was an error
- if (++mcp23018_reset_loop == 0) {
- // if (++mcp23018_reset_loop >= 1300) {
- // since mcp23018_reset_loop is 8 bit - we'll try to reset once in 255 matrix scans
- // this will be approx bit more frequent than once per second
- print("trying to reset mcp23018\n");
- mcp23018_status = init_mcp23018();
- if (mcp23018_status) {
- print("left side not responding\n");
- } else {
- print("left side attached\n");
- }
- }
- }
+#ifdef DEBUG_BALLER
+ if (pRprt.x != 0 || pRprt.y != 0)
+ xprintf("X: %d Y: %d\n", pRprt.x, pRprt.y);
+#endif
+
+ if ((pBtn != trkBtnState) && ((pBtn >> 6) == 0)) pRprt.buttons |= MOUSE_BTN1;
+ if ((pBtn != trkBtnState) && ((pBtn >> 6) == 1)) pRprt.buttons &= ~MOUSE_BTN1;
+
+ // Save state, push update
+ if (pRprt.x != 0 || pRprt.y != 0 || pRprt.h != 0 || pRprt.v != 0 || (trkBtnState != pBtn))
+ pointing_device_set_report(pRprt);
+
+ trkBtnState = pBtn;
+#endif
+
+ // Then the keyboard
+ if (mcp23018_status) { // if there was an error
+ if (++mcp23018_reset_loop == 0) {
+ // if (++mcp23018_reset_loop >= 1300) {
+ // since mcp23018_reset_loop is 8 bit - we'll try to reset once in 255 matrix scans
+ // this will be approx bit more frequent than once per second
+ print("trying to reset mcp23018\n");
+ mcp23018_status = init_mcp23018();
+ if (mcp23018_status) {
+ print("left side not responding\n");
+ } else {
+ print("left side attached\n");
+ }
+ }
+ }
#ifdef DEBUG_MATRIX_SCAN_RATE
matrix_scan_count++;
+
uint32_t timer_now = timer_read32();
- if (TIMER_DIFF_32(timer_now, matrix_timer)>1000) {
+ if (TIMER_DIFF_32(timer_now, matrix_timer) > 1000) {
print("matrix scan frequency: ");
pdec(matrix_scan_count);
print("\n");
- matrix_timer = timer_now;
+ matrix_timer = timer_now;
matrix_scan_count = 0;
}
#endif
+
+ bool changed = false;
for (uint8_t i = 0; i < MATRIX_ROWS_PER_SIDE; i++) {
- select_row(i);
- // and select on left hand
- select_row(i + MATRIX_ROWS_PER_SIDE);
+ // select rows from left and right hands
+ uint8_t left_index = i;
+ uint8_t right_index = i + MATRIX_ROWS_PER_SIDE;
+ select_row(left_index);
+ select_row(right_index);
+
// we don't need a 30us delay anymore, because selecting a
// left-hand row requires more than 30us for i2c.
- // grab cols from left hand
- matrix[i] = debounce_read_cols(i);
- // grab cols from right hand
- matrix[i + MATRIX_ROWS_PER_SIDE] = debounce_read_cols(i + MATRIX_ROWS_PER_SIDE);
+ changed |= store_raw_matrix_row(left_index);
+ changed |= store_raw_matrix_row(right_index);
unselect_rows();
}
+ debounce(raw_matrix, matrix, MATRIX_ROWS, changed);
matrix_scan_quantum();
+
enableInterrupts();
#ifdef DEBUG_MATRIX
return true;
}
-inline
-bool matrix_is_on(uint8_t row, uint8_t col)
-{
- return (matrix[row] & ((matrix_row_t)1<<col));
-}
+inline bool matrix_is_on(uint8_t row, uint8_t col) { return (matrix[row] & ((matrix_row_t)1 << col)); }
-inline
-matrix_row_t matrix_get_row(uint8_t row)
-{
- return matrix[row];
-}
+inline matrix_row_t matrix_get_row(uint8_t row) { return matrix[row]; }
-void matrix_print(void)
-{
+void matrix_print(void) {
print("\nr/c 0123456789ABCDEF\n");
for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
phex(row); print(": ");
}
}
-uint8_t matrix_key_count(void)
-{
+uint8_t matrix_key_count(void) {
uint8_t count = 0;
for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
count += bitpop16(matrix[i]);
}
// Remember this means ROWS
-static void init_cols(void)
-{
+static void init_cols(void) {
// init on mcp23018
// not needed, already done as part of init_mcp23018()
PORTF |= FMASK;
}
-static matrix_row_t read_cols(uint8_t row)
-{
+static matrix_row_t read_cols(uint8_t row) {
if (row < 7) {
if (mcp23018_status) { // if there was an error
return 0;
} else {
uint8_t data = 0;
- mcp23018_status = i2c_start(I2C_ADDR_WRITE, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_write(GPIOB, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_start(I2C_ADDR_READ, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_read_nack(ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status < 0) goto out;
+ mcp23018_status = i2c_start(I2C_ADDR_WRITE, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_write(GPIOB, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_start(I2C_ADDR_READ, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_read_nack(I2C_TIMEOUT); if (mcp23018_status < 0) goto out;
data = ~((uint8_t)mcp23018_status);
mcp23018_status = I2C_STATUS_SUCCESS;
out:
// select on mcp23018
if (mcp23018_status) { // do nothing on error
} else { // set active row low : 0 // set other rows hi-Z : 1
- mcp23018_status = i2c_start(I2C_ADDR_WRITE, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_write(GPIOA, ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
- mcp23018_status = i2c_write(0xFF & ~(1<<row), ERGODOX_EZ_I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_start(I2C_ADDR_WRITE, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_write(GPIOA, I2C_TIMEOUT); if (mcp23018_status) goto out;
+ mcp23018_status = i2c_write(0xFF & ~(1<<row), I2C_TIMEOUT); if (mcp23018_status) goto out;
out:
i2c_stop();
}
EXTRAKEY_ENABLE = yes
CONSOLE_ENABLE = yes
COMMAND_ENABLE = yes
+
+DEBOUNCE_TYPE = eager_pr
projects / qmk_firmware.git / commitdiff