--- /dev/null
+/*
+Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+#define VENDOR_ID 0x20A0
+#define PRODUCT_ID 0x422D
+#define DEVICE_VER 0x0001
+#define MANUFACTURER FT
+#define PRODUCT Mars 8.0
+#define DESCRIPTION A custom TKL Keyboard
+
+#define RGBLED_NUM 20
+
+#define MATRIX_ROWS 7
+#define MATRIX_COLS 14
+// 0 1 2 3 4 5 6 7 8 9 A B C D
+#define MATRIX_ROW_PINS { B0, B1, B2, B3, B5, B6, B7 }
+#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 }
+#define UNUSED_PINS {}
+
+#define DIODE_DIRECTION COL2ROW
+#define DEBOUNCING_DELAY 5
+
+#define NO_BACKLIGHT_CLOCK
+#define BACKLIGHT_LEVELS 1
+#define RGBLIGHT_ANIMATIONS
+
+#define NO_UART 1
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
--- /dev/null
+{
+ "keyboard_name": "Mars 8.0",
+ "url": "",
+ "maintainer": "qmk",
+ "width": 18.25,
+ "height": 6.5,
+ "layouts": {
+ "LAYOUT_tkl_ansi": {
+ "layout": [{"x":0, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6.5, "y":0}, {"x":7.5, "y":0}, {"x":8.5, "y":0}, {"x":9.5, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15.25, "y":0}, {"x":16.25, "y":0}, {"x":17.25, "y":0}, {"x":0, "y":1.5}, {"x":1, "y":1.5}, {"x":2, "y":1.5}, {"x":3, "y":1.5}, {"x":4, "y":1.5}, {"x":5, "y":1.5}, {"x":6, "y":1.5}, {"x":7, "y":1.5}, {"x":8, "y":1.5}, {"x":9, "y":1.5}, {"x":10, "y":1.5}, {"x":11, "y":1.5}, {"x":12, "y":1.5}, {"x":13, "y":1.5, "w":2}, {"x":15.25, "y":1.5}, {"x":16.25, "y":1.5}, {"x":17.25, "y":1.5}, {"x":0, "y":2.5, "w":1.5}, {"x":1.5, "y":2.5}, {"x":2.5, "y":2.5}, {"x":3.5, "y":2.5}, {"x":4.5, "y":2.5}, {"x":5.5, "y":2.5}, {"x":6.5, "y":2.5}, {"x":7.5, "y":2.5}, {"x":8.5, "y":2.5}, {"x":9.5, "y":2.5}, {"x":10.5, "y":2.5}, {"x":11.5, "y":2.5}, {"x":12.5, "y":2.5}, {"x":13.5, "y":2.5, "w":1.5}, {"x":15.25, "y":2.5}, {"x":16.25, "y":2.5}, {"x":17.25, "y":2.5}, {"x":0, "y":3.5, "w":1.75}, {"x":1.75, "y":3.5}, {"x":2.75, "y":3.5}, {"x":3.75, "y":3.5}, {"x":4.75, "y":3.5}, {"x":5.75, "y":3.5}, {"x":6.75, "y":3.5}, {"x":7.75, "y":3.5}, {"x":8.75, "y":3.5}, {"x":9.75, "y":3.5}, {"x":10.75, "y":3.5}, {"x":11.75, "y":3.5}, {"x":12.75, "y":3.5, "w":2.25}, {"x":0, "y":4.5, "w":2.25}, {"x":2.25, "y":4.5}, {"x":3.25, "y":4.5}, {"x":4.25, "y":4.5}, {"x":5.25, "y":4.5}, {"x":6.25, "y":4.5}, {"x":7.25, "y":4.5}, {"x":8.25, "y":4.5}, {"x":9.25, "y":4.5}, {"x":10.25, "y":4.5}, {"x":11.25, "y":4.5}, {"x":12.25, "y":4.5, "w":2.75}, {"x":16.25, "y":4.5}, {"x":0, "y":5.5, "w":1.25}, {"x":1.25, "y":5.5, "w":1.25}, {"x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"x":10, "y":5.5, "w":1.25}, {"x":11.25, "y":5.5, "w":1.25}, {"x":12.5, "y":5.5, "w":1.25}, {"x":13.75, "y":5.5, "w":1.25}, {"x":15.25, "y":5.5}, {"x":16.25, "y":5.5}, {"x":17.25, "y":5.5}]
+ },
+
+ "LAYOUT_tkl_iso": {
+ "layout": [{"x":0, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6.5, "y":0}, {"x":7.5, "y":0}, {"x":8.5, "y":0}, {"x":9.5, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15.25, "y":0}, {"x":16.25, "y":0}, {"x":17.25, "y":0}, {"x":0, "y":1.5}, {"x":1, "y":1.5}, {"x":2, "y":1.5}, {"x":3, "y":1.5}, {"x":4, "y":1.5}, {"x":5, "y":1.5}, {"x":6, "y":1.5}, {"x":7, "y":1.5}, {"x":8, "y":1.5}, {"x":9, "y":1.5}, {"x":10, "y":1.5}, {"x":11, "y":1.5}, {"x":12, "y":1.5}, {"x":13, "y":1.5, "w":2}, {"x":15.25, "y":1.5}, {"x":16.25, "y":1.5}, {"x":17.25, "y":1.5}, {"x":0, "y":2.5, "w":1.5}, {"x":1.5, "y":2.5}, {"x":2.5, "y":2.5}, {"x":3.5, "y":2.5}, {"x":4.5, "y":2.5}, {"x":5.5, "y":2.5}, {"x":6.5, "y":2.5}, {"x":7.5, "y":2.5}, {"x":8.5, "y":2.5}, {"x":9.5, "y":2.5}, {"x":10.5, "y":2.5}, {"x":11.5, "y":2.5}, {"x":12.5, "y":2.5}, {"x":13.75, "y":2.5, "w":1.25, "h":2}, {"x":15.25, "y":2.5}, {"x":16.25, "y":2.5}, {"x":17.25, "y":2.5}, {"x":0, "y":3.5, "w":1.75}, {"x":1.75, "y":3.5}, {"x":2.75, "y":3.5}, {"x":3.75, "y":3.5}, {"x":4.75, "y":3.5}, {"x":5.75, "y":3.5}, {"x":6.75, "y":3.5}, {"x":7.75, "y":3.5}, {"x":8.75, "y":3.5}, {"x":9.75, "y":3.5}, {"x":10.75, "y":3.5}, {"x":11.75, "y":3.5}, {"x":12.75, "y":3.5}, {"x":0, "y":4.5, "w":1.25}, {"x":1.25, "y":4.5}, {"x":2.25, "y":4.5}, {"x":3.25, "y":4.5}, {"x":4.25, "y":4.5}, {"x":5.25, "y":4.5}, {"x":6.25, "y":4.5}, {"x":7.25, "y":4.5}, {"x":8.25, "y":4.5}, {"x":9.25, "y":4.5}, {"x":10.25, "y":4.5}, {"x":11.25, "y":4.5}, {"x":12.25, "y":4.5, "w":2.75}, {"x":16.25, "y":4.5}, {"x":0, "y":5.5, "w":1.25}, {"x":1.25, "y":5.5, "w":1.25}, {"x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"x":10, "y":5.5, "w":1.25}, {"x":11.25, "y":5.5, "w":1.25}, {"x":12.5, "y":5.5, "w":1.25}, {"x":13.75, "y":5.5, "w":1.25}, {"x":15.25, "y":5.5}, {"x":16.25, "y":5.5}, {"x":17.25, "y":5.5}]
+ }
+ }
+}
--- /dev/null
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here
--- /dev/null
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+ QMKBEST = SAFE_RANGE,
+ QMKURL
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ [0] = LAYOUT_tkl_ansi(
+ KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_BRK, \
+ KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_INS, KC_HOME, KC_PGUP, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_DEL, KC_END, KC_PGDN, \
+ KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, \
+ KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, MO(1), KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT \
+ ),
+ [1] = LAYOUT_tkl_ansi(
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_MUTE, KC_VOLD, KC_VOLU, \
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MSEL, \
+ _______, _______, _______, KC_CALC, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ \
+ ),
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+ switch (keycode) {
+ case QMKBEST:
+ if (record->event.pressed) {
+ // when keycode QMKBEST is pressed
+ SEND_STRING("QMK is the best thing ever!");
+ } else {
+ // when keycode QMKBEST is released
+ }
+ break;
+ case QMKURL:
+ if (record->event.pressed) {
+ // when keycode QMKURL is pressed
+ SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER));
+ } else {
+ // when keycode QMKURL is released
+ }
+ break;
+ }
+ return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}
--- /dev/null
+# The default keymap for Mars 8.0
\ No newline at end of file
--- /dev/null
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "mars80.h"
+
+#include "rgblight.h"
+#include "i2c_master.h"
+#include "quantum.h"
+
+#ifdef RGBLIGHT_ENABLE
+extern rgblight_config_t rgblight_config;
+
+void rgblight_set(void) {
+ if (!rgblight_config.enable) {
+ for (uint8_t i = 0; i < RGBLED_NUM; i++) {
+ led[i].r = 0;
+ led[i].g = 0;
+ led[i].b = 0;
+ }
+ }
+
+ i2c_init();
+ i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+}
+#endif
+
+void matrix_init_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+ if (rgblight_config.enable) {
+ i2c_init();
+ i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+ }
+#endif
+ // call user level keymaps, if any
+ matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+ rgblight_task();
+#endif
+ matrix_scan_user();
+ /* Nothing else for now. */
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+void backlight_init_ports(void) {
+ // initialize pins D0, D1, D4 and D6 as output
+ setPinOutput(D0);
+ setPinOutput(D1);
+ setPinOutput(D4);
+ setPinOutput(D6);
+
+ // turn backlight LEDs on
+ writePinHigh(D0);
+ writePinHigh(D1);
+ writePinHigh(D4);
+ writePinHigh(D6);
+}
+
+void backlight_set(uint8_t level) {
+ if (level == 0) {
+ // turn backlight LEDs off
+ writePinLow(D0);
+ writePinLow(D1);
+ writePinLow(D4);
+ writePinLow(D6);
+ } else {
+ // turn backlight LEDs on
+ writePinHigh(D0);
+ writePinHigh(D1);
+ writePinHigh(D4);
+ writePinHigh(D6);
+ }
+}
\ No newline at end of file
--- /dev/null
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+
+#define LAYOUT_tkl_iso( \
+ k11, k13, k14, k15, k16, k18, k19, k1A, k1B, k1C, k10, k1D, k12, k02, k03, k00, \
+ k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, k20, k2D, k07, k06, k05, \
+ k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k30, k0D, k09, k08, \
+ k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k3D, k40, \
+ k51, k4D, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D, \
+ k61, k62, k63, k65, k69, k6A, k6B, k6C, k60, k6D, k68 \
+) \
+{ \
+ { k00, KC_NO, k02, k03, KC_NO, k05, k06, k07, k08, k09, KC_NO, KC_NO, KC_NO, k0D }, \
+ { k10, k11, k12, k13, k14, k15, k16, KC_NO, k18, k19, k1A, k1B, k1C, k1D }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, KC_NO, k2D }, \
+ { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k3D }, \
+ { k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k4D }, \
+ { KC_NO, k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D }, \
+ { k60, k61, k62, k63, KC_NO, k65, KC_NO, KC_NO, k68, k69, k6A, k6B, k6C, k6D }, \
+}
+
+#define LAYOUT_tkl_ansi( \
+ k11, k13, k14, k15, k16, k18, k19, k1A, k1B, k1C, k10, k1D, k12, k02, k03, k00, \
+ k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, k20, k2D, k07, k06, k05, \
+ k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k30, k3D, k0D, k09, k08, \
+ k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k40, \
+ k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D, \
+ k61, k62, k63, k65, k69, k6A, k6B, k6C, k60, k6D, k68 \
+) \
+{ \
+ { k00, KC_NO, k02, k03, KC_NO, k05, k06, k07, k08, k09, KC_NO, KC_NO, KC_NO, k0D }, \
+ { k10, k11, k12, k13, k14, k15, k16, KC_NO, k18, k19, k1A, k1B, k1C, k1D }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, KC_NO, k2D }, \
+ { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k3D }, \
+ { k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, KC_NO }, \
+ { KC_NO, k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k5B, k5C, k5D }, \
+ { k60, k61, k62, k63, KC_NO, k65, KC_NO, KC_NO, k68, k69, k6A, k6B, k6C, k6D }, \
+}
--- /dev/null
+# Mars 8.0
+
+TKL Keyboard with in switch backlight and RGB Underglow.
+
+Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin)
+Hardware Supported: Mars 8.0 PCB
+Hardware Availability: [Geekhack Group Buy](https://geekhack.org/index.php?topic=93723.0)
+
+Make example for this keyboard (after setting up your build environment):
+
+ make ft/mars80:default
+
+Flashing
+
+ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods.
+
+**Reset Key:** Hold down the key located at `K00`, commonly programmed as `Pause/Break` while plugging in the keyboard.
+
+Windows:
+1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
+2. Place your keyboard into reset.
+3. Press the `Find Device` button and ensure that your keyboard is found.
+4. Press the `Open .hex File` button and locate the `.hex` file you created.
+5. Press the `Flash Device` button and wait for the process to complete.
+
+macOS:
+1. Install homebrew by typing the following:
+ ```
+ /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"
+ ```
+2. Install `crosspack-avr`.
+ ```
+ brew cask install crosspack-avr
+ ```
+3. Install the following packages:
+ ```
+ brew install python3
+ pip3 install pyusb
+ brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+ ```
+4. Place your keyboard into reset.
+5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file.
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
--- /dev/null
+# Copyright 2019 Luiz Ribeiro <luizribeiro@gmail.com>
+#
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+
+# MCU name
+MCU = atmega32a
+PROTOCOL = VUSB
+
+# unsupported features for now
+NO_UART = yes
+NO_SUSPEND_POWER_DOWN = yes
+
+# processor frequency
+F_CPU = 12000000
+
+# Bootloader
+# This definition is optional, and if your keyboard supports multiple bootloaders of
+# different sizes, comment this out, and the correct address will be loaded
+# automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = bootloadHID
+
+# build options
+BOOTMAGIC_ENABLE = no
+MOUSEKEY_ENABLE = no
+EXTRAKEY_ENABLE = yes
+CONSOLE_ENABLE = yes
+COMMAND_ENABLE = yes
+BACKLIGHT_ENABLE = yes
+RGBLIGHT_ENABLE = yes
+RGBLIGHT_CUSTOM_DRIVER = yes
+
+OPT_DEFS = -DDEBUG_LEVEL=0
+
+SRC += i2c_master.c
+
+# programming options
+PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
+
+LAYOUTS = tkl_ansi tkl_iso
--- /dev/null
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
+ */
+
+#pragma once
+
+#include "config.h"
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT 3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT 2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC 0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT 4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER 3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT 0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE 0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL 1
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED 0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+#define USB_CFG_MAX_BUS_POWER 500
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE 1
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ 0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL 0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE 0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS 0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF 1
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ * in YL, TCNT0
+ * sts timer0Snapshot, YL
+ * endm
+ * #endif
+ * #define USB_SOF_HOOK myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING 0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC 0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION 0x00, 0x02
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME 'f', 't'
+#define USB_CFG_VENDOR_NAME_LEN 2
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME 'm', 'a', 'r', 's', '8', '0'
+#define USB_CFG_DEVICE_NAME_LEN 6
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS 0
+#define USB_CFG_DEVICE_SUBCLASS 0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS 3 /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ * you want RAM pointers.
+ * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ * in static memory is in RAM, not in flash memory.
+ * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ * the driver must know the descriptor's length. The descriptor itself is
+ * found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ * char usbDescriptorDevice[];
+ * char usbDescriptorConfiguration[];
+ * char usbDescriptorHidReport[];
+ * char usbDescriptorString0[];
+ * int usbDescriptorStringVendor[];
+ * int usbDescriptorStringDevice[];
+ * int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ * USB_CFG_DESCR_PROPS_DEVICE
+ * USB_CFG_DESCR_PROPS_CONFIGURATION
+ * USB_CFG_DESCR_PROPS_STRINGS
+ * USB_CFG_DESCR_PROPS_STRING_0
+ * USB_CFG_DESCR_PROPS_STRING_VENDOR
+ * USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ * USB_CFG_DESCR_PROPS_HID
+ * USB_CFG_DESCR_PROPS_HID_REPORT
+ * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int serialNumberDescriptor[] = {
+ * USB_STRING_DESCRIPTOR_HEADER(6),
+ * 'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE 0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
+#define USB_CFG_DESCR_PROPS_STRINGS 0
+#define USB_CFG_DESCR_PROPS_STRING_0 0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
+#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID 0
+#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID_REPORT 0
+#define USB_CFG_DESCR_PROPS_UNKNOWN 0
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG MCUCR */
+/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR 0 */
+/* #define USB_INTR_ENABLE GIMSK */
+/* #define USB_INTR_ENABLE_BIT INT0 */
+/* #define USB_INTR_PENDING GIFR */
+/* #define USB_INTR_PENDING_BIT INTF0 */
+/* #define USB_INTR_VECTOR INT0_vect */
+
+/* Set INT1 for D- falling edge to count SOF */
+/* #define USB_INTR_CFG EICRA */
+#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
+/* #define USB_INTR_CFG_CLR 0 */
+/* #define USB_INTR_ENABLE EIMSK */
+#define USB_INTR_ENABLE_BIT INT1
+/* #define USB_INTR_PENDING EIFR */
+#define USB_INTR_PENDING_BIT INTF1
+#define USB_INTR_VECTOR INT1_vect
projects / qmk_firmware.git / commitdiff